User manual ZANKER ZKK9410

[. . . ] Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages. There must be adequate ventilation round the back of the appliance and any damage to the refrigerant circuit must be avoided. For freezers only (except built-in models): an ideal location is the cellar or basement. Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances, unless they are approved for this purpose by the manufacturer. s s Use s s s The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only. [. . . ] Do not use detergents or abrasive powders, as these will damage the finish. 47 Instructions for totally built-in appliances Dimensions of the recess Model Height Depth Width ZKK 9408 880 mm 550 mm 560 mm ZKK 9410 1030 mm 550 mm 560 mm ZKK 9412 1225 mm 550 mm 560 mm 50 mm The appliance's door has been locked in position for transport by means of pins on both sides. According to the door opening direction, remove relevant pins at the top and at the bottom. Push appliance into the housing until stop strip (A) touches the kitchen unit. min. 2 A D022 Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. Fig. 3 PR162 48 Press in the joint covers between the appliance and the kitchen unit. Fig. 4 D724 Apply covers (B) on joint cover lugs and into hinge holes. Fig. 5 B D726 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. Fig. 6 H 20m m D094 Open both the appliance door and that of the kitchen unit to approx. Hold the doors of the appliance and the unit together and mark the holes. Fig. 7 8mm PR34 49 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Fig. 8 PR35 Inner door reversal Using a screwdriver release bracket (1) by pressing on the internal spring (Fig. 9) and withdraw it from its seat together with the door; remove plug (2) and fit it in the hole left open on the opposite side; turn the door through 180°, remove the bracket (1) and refit it on the opposite side. Refit the door and insert the top pin and bottom bracket (1), pushing it into place. To ensure correct storage of food, the door is fitted with a simple spring device which holds it in the open position until it is properly closed. Fig. 9 180° 2 1 PR140 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. [. . . ] Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: pull out the plug from the wall socket or turn the thermostat knob to the «O» setting; remove any stored food, wrap it in several layers of newspaper and put it in a cool place; leave the door open, place a basin on the top shelf of the refrigerator compartment, under the drain hole, remove the plug as shown in the figure; when defrosting is completed, dry the interior thoroughly and refit the plug; keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. 13 PR151 Important A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 55 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. [. . . ]