User manual ZANKER THKE5000

[. . . ] · Repairs to the appliance are only to be carried out by approved service engineers. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. If your appliance needs repairing, please contact your local AEG customer center or your dealer. 3 Please follow these instructions, otherwise the warranty is void in the event of damages. · Flush-mounted appliances may only be operated following installation in suitable installation cabinets and workplaces which conform to the relevant standards. [. . . ] This is a characteristic of all glass ceramic cooking zones and does not impair either the function or the life of the appliance. TOUCH CONTROL Sensor Field To operate the TOUCH CONTROL sensor field place your finger from above flat onto the required field until the appropriate displays come on or go out or the required function is carried out. 107 Switching On the Appliance The entire appliance is switched on using the "On/Off" n sensor field. The digital displays will show j and the decimal point will flash. 3 Once the "On/Off" sensor field has been operated to switch on the appliance, one of the cooking zones must be selected within approx. Otherwise the appliance switches off again for safety reasons. Switching Off the Appliance To switch off the appliance completely activate the "On/Off" n sensor field. 1 second. 3 When an individual cooking zone or the entire hob is switched off, any residual heat is shown with an h (for "Hot") in the digital display for the appropriate cooking zones. 108 Cooking Zone Selection To select the required cooking zone touch the corresponding sensor field for approx. A zero with a decimal point will light up in the appropriate cooking zone display window =. 3 The decimal point indicates that settings may only be made for this cooking zone. 109 Heat Setting Selection + and For setting and adjusting the heat setting (!Lower the heat setting with sensor field -. 3 If several cooking zones are being used simultaneously, the required cooking zone must be selected by touching the appropriate sensor field before adjusting the heat setting. The decimal point in the display shows which cooking zone has been selected. 110 Switching off a Cooking Zone 1. Touch sensor fields + and - simultaneously to switch off or turn sensor field - back to zero. 3 A cooking zone may only be switched off when the decimal point is on in the cooking zone display. Residual Heat Indicator When an individual cooking zone or the entire hob is switched off, any residual heat is shown with an h (for "Hot") in the digital display for the appropriate cooking zones. Even after the cooking zone has been switched off, the residual heat indicator only goes out when the cooking zone is cold. 2 1 You can use the residual heat for melting and keeping food warm. As long as the residual heat indicator is illuminated, there is a risk of burns. 111 1 Important!If the power supply is interrupted the h symbol will also go out and information about residual heat will no longer be available. Do not attempt any further repairs if the following instructions do not help in each specific case. 1 Warning!Repairs to the appliance are only to be carried out by approved service engineers. Improperly effected repairs may result in considerable risk to the user. If your appliance needs repairing, please contact your specialist dealer or customer service. What to do if . . . . . . . Check, whether ­ the mains fuse (in the household fuse box) is intact. ­ the cooking zones are set to the required setting to finish cooking (see section "Cooking"). ­ the cooking zones have been switched off by the safety cutout (see section "Safety Functions"). Check, whether ­ the control panel is locked (see section "Child-Safety Device"). ­ more than 10 seconds have elapsed between operating the On/Off button and switching on the desired cooking zone (see section "Switching on the appliance"). ­ the touch controls are entirely or partly covered by liquid or by a wet cloth. 120 . . . the whole indicator section for residual heat, except h, will fail all of a sudden? [. . . ] Please note that proof of purchase is required for any in-guarantee service calls. 122 Installation Instructions 1 Important!The new appliance may only be installed and connected by a registered specialist. Please observe this instruction, otherwise the warranty will not cover any damage that may occur. Technical Data Appliance Dimensions Width Depth Height 572 mm 502 mm 49 mm Cut-Out Dimensions Width Depth Corner radius 560 mm 490 mm R5 Power Consumption Front left cooking zone ø 210 mm Back left cooking zone ø 145 mm Back right cooking zone ø 180 mm Front right cooking zone ø 145 mm Heating Element Voltage Total Connected Load max. 2300 W 1200 W 1800 W 1200 W 230 V ~50 Hz 6. 5 kW 123 Regulations, Standards, Directives This appliance meets the following standards: · EN 60 335-1 and EN 60 335-2-6 relating to the safety of electrical appliances for household use and similar purposes and · DIN 44546 / 44547 / 44548 relating to the operating features of electric cookers for household use. [. . . ]