User manual ZANKER KE5000

[. . . ] Tips and information about the economical and environmentally friendly use of the machine are marked with the clover symbol. If you require assistance or advice on your appliance, please contact our Customer Care Department by letter or telephone: Customer Care Department AEG Domestic Appliances 55-77 High Street Slough Berkshire SL 1 1DZ Tel: 08705 350350 3 2 Printed on environmentally friendly paper . . . 15 15 15 15 15 15 17 18 18 18 18 19 19 20 21 21 3 Content Programme tables . 43 4 1 Important Safety Information Your safety is of paramount importance, please ensure you read these warnings before installing or using the appliance. [. . . ] 0 Press against the filter lid until it catches into the locking device. 3 The filter lid cannot catch shut without the fluff filter in place and the door cannot be closed. The dryer must not be operated with a damaged or blocked fluff filter. 1 20 Drying Cleaning the heat exchanger 1 Important!When the HEAT EXCHANGER display lights, it is essential to clean the heat exchanger. In addition energy consumption will be increased if the heat exchanger unit is covered with fluff. 0 Open the door. 0 Press on the two tabs to unlatch and take off the removable plinth. 0 Turn the two securing disks through a quarter turn each outwards. 0 Pull the heat exchanger out of the base by the handle. 0 Clean the heat exchanger, best with a hand-held brush or by rinsing with a hand-held shower head. The water removal slits on the rear of the heat exchanger must be free too. 1 Important!0 Reinsert and push in and turn each one of the two securing disks through a quarter turn inwards. The words "top ­ oben ­ en haut" must be at the top. The dryer must not be operated without heat exchanger. 1 Switch-off the dryer 0 Turn the programme selector to the OFF position. 21 Programme tables Programme group COTTONS care symbols R, Q; maximum load 5 kg Programme EXTRA DRY INTENSIVE DRY Laundry Type Heavy weight or multilayered fabrics Thick textiles that are to be thoroughly dried. The dryer is then no longer reliably able to recognise how dry the washing is. When the washing is removed from the dryer it will be damper than you expect. 0 Wipe the inside of the drum and the drum fins with white vinegar to avoid any residues/deposits effecting the sensors. This is particularly important if you regulary use fabric conditioning sheets or dry starched items in the dryer. 25 Cleaning and maintenance Cleaning the panel and operating parts 1 Warning!Only use warm water. Cleaning the door seal 0 Rub the door seal with a damp cloth immediately after the drying procedure. Cleaning the heat exchanger 1 Important!When the HEAT EXCHANGER display lights, it is essential to clean the heat exchanger. In addition energy consumption will be increased if the heat exchanger unit is covered with fluff. See the section "Drying, cleaning the heat exchanger". 26 Programming possibilities The electronic control system of your laundry dryer provides you with the possibility to adapt some functions of the dryer permanently to your requirements. Purpose "Laundry protection": If you want to "lock" the selected drying programme (the selected programme setting cannot be changed during the drying process with the programme selector or with the SPECIAL CARE or QUICK button): When "Washing Protection" is enabled, the drying programme always runs at reduced heater power (SPECIAL CARE Function). Execution When a drying programme is set with the programme selector and the START button has been pressed: - Hold the SPECIAL CARE button depressed for five seconds. The programme execution display flashes for five seconds and the laundry protection is then switched-on. If an attempt is nevertheless made to change the programme setting, the programme execution display flashes; after pressing the SPECIAL CARE or QUICK button, it flashes for five seconds; on turning the programme selector it flashes until the programme selector is returned to the initial setting. [. . . ] Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is located inside the door. The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS 1362) fuse must be used. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow : Earth Blue : Neutral Brown : Live Green & Yellow Blue Brown Cord Clamp 38 Electrical Connection · The wire coloured green and yellow must be connected to the terminal marked with the letter "E" or by the earth symbol or coloured green and yellow · The wire coloured blue must be connected to the terminal "N" or coloured black. [. . . ]