User manual ZANKER ICO30B

[. . . ] You MUST read it carefully before installing or using the appliance. Installation q q Check your dishwasher for any transport damage. For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way. Any electrical and plumbing work required to install this appliance should be carried out by a qualified and competent person. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. [. . . ] Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket. Screw on the cap tightly turning it clockwise until it stops with a click. SR14 LE SA UT ZO LT SA LZ SA L SE BR07 BR14 Ensure that the lid is closed after every refill. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash. This would damage the appliance. The salt container will require topping up periodically. A salt indicator light on the control panel will come on when the salt has finished. The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salts that take longer to dissolve then this can take longer. Do not worry if water over flows from the unit when filling with salt, this is quite normal. Adjusting the dose According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage). Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes. BR09 Top up the rinse aid when the indicator light on the control panel illuminates. 25 If you are using dishwasher detergent that includes the rinse aid function, this must be placed in the detergent compartment. In this case the inflow of the rinse aid must be deactivated, in order to avoid a double dosage . Deactivation/activation of the inflow of rinse aid (The dishwasher must be switched off) When the inflow of rinse aid has been deactivated, also the rinse aid indicator light on the control panel is automatically deactivated. Move the front runner stops (A) of the upper basket outwards and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. When the basket is in the higher position you will not be able to use the cup rack(s). US73 In case that plates are loaded in the upper basket: load them starting from the rear positions of the basket; tilting them slightly forwards and avoiding the front positions near the door. US71 RC01 After loading your machine always close the door, as an open door can be a hazard. Before closing the door, ensure that the spray arms can rotate freely. 28 Use of detergent Only use detergents specifically designed for use in dishwashers. Using no more then the correct amount of detergent contributes to reducing pollution. Prior to the start of a wash programme. The detergent is released during the washing phase. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. Fill with detergent 1. The marking indicates the dosing levels: 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent 3. All programmes with prewash need a little amount of detergent (5/10 g) to be added in the adjacent chamber (3). DE19 DE22 4. Close the lid and press until it locks in place. Different kinds of detergent Detergent tablets Detergent tablets of different brands dissolve at different speeds. For this reason some detergent tablets cannot dissolve and develop their full cleaning power during short programmes. Therefore please use long programmes when using detergent tablets, to ensure the complete removal of detergent residuals. [. . . ] Remove the flat filter (D) from the base of the washing compartment and clean both faces thoroughly. MA31 7. Place the coarse/fine filter (A/B) in the microfilter C) and press together. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. 32 What to do, when. . . Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer. . . . a flashing fault code appears The dishwasher will not start or stops during operation. [. . . ]