User manual ZANKER CP10BWN

[. . . ] Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. s s Care should be taken when cleaning the bottom door seal and hinge area as any exposed metal edges may cut if care is not taken. This product should be serviced by an authorised Service engineer, and only genuine spare parts should be used. [. . . ] This will avoid lime deposits on crockery and the inner tub. 33 PUD04GB M M IN AX Using your appliance Loading your appliance Before placing dishes in the machine, remove any scraps of food, to avoid clogging the filters and consequently reducing the performance. Open the door and slide out the baskets to load the dishes. The lower basket The lower basket is designed to take saucepans, lids, plates (up to 27 cm in diameter), salad bowls, cutlery etc. Serving dishes and large lids should be arranged around the edge of the basket, ensuring that the upper spray arm can turn freely. UI33 IEC 436 / DIN 44990 The cutlery basket Long bladed knives stored in an upright position are a potential hazard. UI19 Long and/or sharp items of cutlery such as carvings knives must be positioned horizontally in the upper basket. Cutlery should be placed in the removable cutlery basket with the handles facing downwards. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Arrange the spoons, dessert spoons, knives and other small items of cutlery in the racks on both sides of the cutlery basket. UI03 34 PBA09GB The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 24 cm in diameter), salad bowls, cups and glasses; Glasses with long stems can be placed upside down in the raised cup racks. Larger plates (dinner plates up to 24 cm in diameter) must be loaded in the front part of the upper basket. Light items (plastic bowls etc. ) should be loaded in the upper basket and arranged so they do not move. Before closing the door, ensure that the spray arms can rotate freely. US17 IEC 436 / DIN 44990 Adjusting the height of the upper basket If washing very large plates (over 27 cm and up to 31 cm in diameter) you can load them in the lower basket after moving the upper basket to the higher position. To move to the higher position proceed as follows: Move the front runner stops (A) of the upper basket outward and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. We recommend every 3 months to run a 65°C wash programme without dishes using detergent. Cleaning the central filter (After each wash) Scraps of food may accumulate in the drain filter (A) and should be removed by rinsing the filter under running water. To remove the drain filter: simply pull it out by the handle. Once cleaned, refit the filter by pushing it back to its original position until it engages. A MA04 Cleaning the large filter (Every two months) If necessary clean the large filter (B) on both sides under running water, using a brush. To remove the large filter: Remove the spray arm by pulling it upward on one side. Turn the column (C) anticlockwise by 90° and then slide out the filter. Once cleaned refit it following the above instructions in reverse order. Ensure the filter is in its original position, the handle of the drain filter should be pointing towards the front of the appliance. Incorrect repositioning and fitting of the filters will produce poor washing results. Cleaning the filters is vital to ensure correct operation of the machine. 90° B C MA05 39 PMC01GB External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc. . . . ). Prolonged periods of non-operation If you are not using the machine for any period of time you are advised to: Unplug the appliance and then turn off the water; Fill the rinse aid dispenser; Leave the door ajar to prevent the formation of any unpleasant smells; Leave the inside of the machine clean. Frost precautions Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it. Moving the machine If you have to move the machine (moving house etc. . . . ): Unplug it; Turn the water tap off; Remove the water inlet and discharge; Pull the machine out together with the hoses. Avoid over tilting the machine during transport. 40 PMC02GB Something not working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below. Symptom The machine will not start Solution s s s s The door has not been properly closed. Dishes are rattling against each other, (refer to "Loading your machine"). The dishes have been left too long inside the machine. The dishwasher does not fill with water s s s s The filters are blocked s s The dishwasher will not drain s s s s The machine is noisy s s The door is difficult to close The dishes are not clean (poor wash) s s s s s s s s s s s Visible lime deposits or white film on the dishes The dishes are not quite dry s s s 41 PSN01GB If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. [. . . ] The sink plug must not be in place when the machine is draining as this could cause the water to siphon back into the machine. Ø Ø 18 Ø 21 18 + 2 m max CS11 Electrical connection Before plugging the appliance into the wall socket, make sure that: The mains voltage corresponds to the voltage given in the "Technical specifications". The meter, fuses, mains power supply and wall socket can all take the maximum load required. Make sure that the socket and plug are compatible without having to use any type of adaptor. The manufacture accepts no liability for failure to observe the above safety precautions. This appliance complies with the following E. E. C. [. . . ]