User manual YAMAHA MG16XU/MG16

[. . . ] Owner’s Manual Precautions Quick Start Guide Troubleshooting pages 5, 6 pages 9 to 11 page 29 to 31 EN The above warning is located on the rear of the unit. l’avertissement ci-dessus est situé à l’arrière de l’appareil. Explanation of Graphical Symbols Explication des symboles The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. l’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « tension dangereuse » non isolée à l’intérieur de l’appareil , pouvant être suffisamment élevée pour constituer un risque d’électrocution. [. . . ] Mono input channels have a [PAD] switch r that lets you change the range of this control. [PAD] switch ON OFF Range -6 dB to +38 dB +20 dB to +64 dB o [LINE /USB ] switch (XU models) Switches the audio source input on CH19/20 USB IN {CH15/ 16 USB IN} {CH11/12USB IN} between the [LINE] stereo input jack and the [USB 2. 1 [AUX 1 – 4] knobs [PRE] switches [AUX (2, 4)/FX] knobs MG20XU/MG16XU: [AUX1], [AUX2 – 3], [AUX4/FX] MG20/MG16: [AUX1], [AUX2 – 4] MG12XU: [AUX1], [AUX2/FX] MG12: [AUX1 – 2] 3 Band [MID] Sweep 3 Band 2 Band The levels of each signal sent to the AUX 1 – 4 buses from each channel can be adjusted independently. On stereo input channels, the Line L (odd) and Line R (even) input signals are mixed before being sent to each AUX bus. Adjust the knobs so that they are near or at the “t” (nominal) position. NOTE • The [AUX1] knob indicated “PRE” adjusts the level of the prefader signal (before fader adjustment). Equalization Types and Characteristics 3 Band [MID] Sweep MG20XU/ MG20 MG16XU/ MG16 MG12XU/ MG12 CH 1 – 12 CH 1 – 8 — 3 Band CH 13/14 – 19/20 CH 9/10 – 15/16 CH 1 – 7/8 2 Band — — CH 9/10 – 11/12 • The [PRE] switch on [AUX1] and [AUX2] can be used to select whether the pre-fader ( ) (the signal before fader adjustment) or post fader ( ) (the signal after fader adjustment) signal is sent to the AUX bus by the [PRE] switch. € The [AUX4/FX] and [AUX2/FX] knobs are used to adjust the level of the signal sent to the FX bus (built-in effects) in addition to the AUX bus. The same signal level is sent to the AUX buses and FX buses connected to these knobs. Turning the knob to the right amplifies (boosts) the corresponding frequency band, while turning it to the left attenuates (cuts) the band. Setting the knob to the middle “t” position produces a flat response in the corresponding band. The upper knob sets the variable mid frequency, while the lower knob sets the amount of attenuation or boost (counterclockwise/clockwise) for the range. The following table shows the EQ type, frequency, and cut/ boost range for each of the three bands. 2 [PAN] knobs [PAN/BAL] knobs [BAL] knobs * The signals from mono input jacks of the MG20XU/MG20 and MG16XU/MG16 can be adjusted from 250 Hz to 5 kHz. This knob adjusts the volume balance of each channel sent to the STEREO L/R bus. When the knob is set to the 12 o’clock position, the channel’s sound will be sent to the L and R of the STEREO L/R bus at the same volume. If the bus assign switch [1-2] or [3-4] is pressed, this knob adjusts the volume balance sent to the GROUP bus. When the knob is set to the 12 o’clock position, the same volume is sent to each GROUP bus. If the knob is turned completely to the left, the signal is sent to the GROUP 1 or GROUP 3 bus only; if the knob is turned completely to the right, the signal is sent to the GROUP 2 or GROUP 4 bus only. 18 MG20XU/MG20/MG16XU/MG16/MG12XU/MG12 Owner’s Manual Controls and Connectors • BAL: Sets the volume balance of the signal sent from each stereo input channel (L/R) to the STEREO L/R bus or GROUP bus. When this knob is set to the 12 o’clock position, the sound of the stereo input channels (L/R) will be sent to the STEREO L/R bus or GROUP 1, 3/2, 4 bus at the same volume. BAL LINE L LINE R STEREO L bus, GROUP 1 bus, GROUP 3 bus STEREO R bus, GROUP 2 bus, GROUP 4 bus These switches determine the bus(es) to which each channel’s signal is sent. [. . . ] XLR type connectors are the standard for microphone connections as well as most professional audio gear. male Female Phone Phone connectors are available in TRS and TS types. TRS types are used for stereo headphone jacks, insert jacks, and also for carrying balanced signals in many cases. TS types are used to carry unbalanced signals -for example, electric guitar cables. [. . . ]