User manual YAMAHA 25NE SERVICE MANUAL

[. . . ] 4 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Attaching the Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I About the Strap Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you cannot locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA 90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high-quality shielded cables. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the user's manual, may cause interference harmful to the operation of other CANADA* THIS DIGITAL APPARATUS DOES NOT EXCEED THE "CLASS B" LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS SET OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS. LE PRESENT APPAREIL NUMERIQUE N'EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX APPAREILS NUMERIQUES DE LA "CLASSE B" PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EDICTE PAR LE MINISTERE DES COMMUNICATIONS DU CANADA. · This applies only to products distributed by Yamaha Canada Music Ltd. · Ceci ne s'applique qu'aux produits distribués par Yamaha Canada Musique Ltée. 2 Your Silent Guitar will give you years of reliable service if you follow the simple rules given below: I Location Do not expose it to the following conditions to avoid deformation, discoloration, or more serious damage. The rods may become damaged. Frame attachment screw 1 w Rod OPEN q First, insert the lower rod into the main body. w Then, insert the upper rod. 3. After confirming that both rods of the left frame are fully inserted, turn the attachment screws clockwise and secure the left frame to the Silent Guitar's main body. · When moving any movable parts, make sure that your fingers or hand do not become pinched in the parts. · Do not tighten the attachment screws when the frame is removed. It will result in the damage of parts, which will cause problems when re-attaching the frame. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. · THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For that reason, we recommend that it be powered with the supplied AC power adaptor for normal use. Always turn the PHONES ON/OFF switch OFF before making AC power connections or replacing the battery. 2. Plug the adaptor's DC output cable into the Silent Guitar's DC IN jack, making sure the plug is firmly inserted into the jack. Plug the AC adaptor into a convenient wall AC power socket. · Battery power is automatically disconnected when the AC adaptor is connected. To prevent leakage we recommend that you remove the batteries from the instrument. [. . . ] The REVERB function can be used for adding reverb to the guitar's tone to produce the live acoustic characteristics experienced in a room or hall. Set the REVERB switch to its "1" position to add the type of reverb usually experienced in a room, or set the switch to its "2" position to add the type of reverb normally experienced in a hall. · When compared to the REVERB switch's REVERB 1 or REVERB 2 positions, the instrument consumes less power when the REVERB switch is in its OFF position. · Some noise is produced when the position of the REVERB switch is changed. When the power is ON, the lamp lights. OFF 1 2 4. Adjusts the volume Adjusts low frequencies Adjusts high frequencies OFF ON REVERB VOLUME BASS TREBLE PHONES I Using the stereo earphones (or stereo output to an external device) When using the instrument with the supplied stereo earphones or a separately purchased pair of headphones, or when you want to send the instrument's stereo output to an external device, use the headphones (PHONES) jack for connecting the earphones or external device. 1. [. . . ]