User manual YAESU PEP2000 UPDATE V0150 AND V11.53

[. . . ] Down load the FT-2000 data file [FT-2000_PEP2000_11-30-09. zip] from the following website: http://www. yaesu. com/indexVS. cfm?cmd=DisplayProducts&ProdCatID=102&encProdID=66EA 91711DFB68C03DED4AD35153E12C&DivisionID=65&isArchived=0 2. Save the FT-2000 data file [FT-2000_PEP2000_11-30-09. zip] to the desktop on your computer. Unzip and Extract the contents of [FT-2000_PEP2000_11-30-09. zip] to the desktop of your computer. You will find the PEP2000_EDSP3 and PEP2000_MAIN folders on your desktop. [. . . ] Double-click the FSW003 icon, displayed on the Program Screen. NOTE: If you receive a "communications error" message on your screen, click on the Configure box and choose a different COM port from the drop down menu. Then click the WRITE button again. (4) (5) When the program opens, confirm that the file AH025_V0150. SFL is highlighted; if not, click on it to highlight it. Remove the black cover from the PGM jack (bottom left on the rear panel). Plug the AC cord into the radio and turn the main power switch on the back of the radio to the ON position. [NOTE: The radio will not show a display now. ] Main Power SW PGM Click on [WRITE] in the program window. (8) Turn off the main power switch, (or turn off the power supply for FT-2000D and wait a minute, until the capacitors discharge) and unplug the AC power cord. (10) Plug the AC power cord into the radio and turn the main power switch on the back of the radio to the ON position (or turn on the power supply for FT-2000D). Press and hold in the [FAST] and [LOCK] keys; while holding them in, press the front power switch to turn the radio on. This resets the radio and locks in the new software. (6) (12) Turn the radio off. Follow the instructions below to update the EDSP. 8-pin mini-DIN PGM-SW 1. I choose the . sfl file of the version V0150 to write in and push WRITE of the screen. Reset the radio to default. NOTE: for a more detailed description see the Main CPU programming. EDSP This procedure is used for uploading new EDSP Software into the FT-2000/D Amateur Transceivers, from your personal computer, using the RS-232C, DB9F to DB9F straight cable. Turn off the main power switch located on the back of the FT-2000 (or turn off the power supply for FT-2000D and wait a minute, until the capacitors discharge) and remove the AC power cord. Connect a serial RS-232C, DB9F to DB9F straight cable to the COM1 connector of your computer and the 9-pin CAT connector on the rear of the transceiver. If you use a USB to serial adapter, you might need to change the COM Port number. Main Power SW CAT 3. Reconnect the power cord and turn ON the main power switch located on the back of the FT-2000 (or turn ON the power supply for FT-2000D). While holding the [DNR][CONT][DNF] buttons, press the front power switch to turn the radio on. On your computer desk top open PEP2000_EDSP folder and find the EDSP-301 icon as shown below. Double-click the EDSP-301 icon, displayed on the Program Screen. 6. If you do not see AH025_V1153 (as in the screen below), then open the "Look in:" window and go to the desktop and find PEP2000_EDSP. Then click the Open button and wait until the program is loaded, and 100% is indicated on the bar graph, [completion!!] will be displayed. NOTE: If you receive a "communications error" message on your screen you should check the COM port number and speed under Device Manager. The writing speed 38. 4kbps is fixed in the download algorithm of the EDSP board so you may need to set the port speed close to 38. 4kbps. [. . . ] Carefully Place the Transceiver bottom side up on a sturdy cleared worktable. Find the micro-switch on the pc board near the rear right hand corner when looking down at the bottom of the FT-2000/D. (See the attached photo. ) (2) (3) (4) (5) (6) Connect a serial cable RS-232C, DB9F to DB9F straight cable to the COM1 connector of your computer and the 9-pin CAT connector on the rear of the transceiver. If you use a USB to serial adapter, you might need to change the COM Port number. [. . . ]