Detailed instructions for use are in the User's Guide.
[. . . ] DUAL BAND FM TRANSCEIVER
FTM-350 SERIES
OPERATING MANUAL
VERTEX STANDARD CO. , LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A.
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD (AUSTRALIA) PTY. , LTD.
Normanby Business Park, Unit 14/45 Normanby Road Notting Hill 3168, Victoria, Australia
Contents
Front Panel Controls & Switches . . . . . . . . . . . . . . . . . . . . . . . . . . 4 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Memory Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the [ALTI] key to change the "barometric" chart to the "altitude" chart. You may also change the time scale of the altitude chart by pressing the [SCALE] key. To return to the "barometric" chart, press the [BARO] key.
32 4
2 3 4
To return to the "Radio" page, press the [FWD] or [BCK] key repeatedly, until the "Radio" Page appears. You may change the barometric and altitude measurement units via Set Mode item "G10 UNIT SELECT" in the "SYSTEM" group (see page 42). : The FGPS-2 GPS Unit requires CT-133 GPS Antenna Cable and CT-136 GPS Antenna Adapter.
FTM-350 SERIES OPERATING MANUAL
23
GPS OPERATION (REQUIRES OPTIONAL GPS ANTENNA UNIT)
When the optional FGPS-1 or FGPS-2 GPS Antenna Unit is installed, the transceiver permits the display of your position (Longitude/Latitude). Before beginning GPS operation, enable the "GPS" page via the Set Mode item "C01 DISPLAY SELECT" in the "DISPLAY" group. See page 35.
1
4
24
3
1 Press the [FWD] or [BCK] key repeatedly, until the "GPS" Page appears.
Your current position (Longitude/Latitude) appears at the upper right of the display, and your current altitude and vehicle speed appears at the lower right of the display. Additionally, your course direction (compass) displays in the left half of the display. Available selections are "Compass Rose (North Up)", "Compass Rose (Heading Up)", and "Compass Tape". Press the [POINT] key to store the current position and date into the "Point" memory, if desired. Available "Point" memories are in four groups, and there are four Channels for each group. Rotate the left side [DIAL] knob to scroll the list and press the [BCK] key to close the list. You may delete an unwanted point from the "Point" memory list by pressing the [DEL] key, if desired.
2 3 4
To return to the "Radio" page, press the [FWD] or [BCK] key repeatedly, until the "Radio" Page appears. You may change the measurement units of the altitude and vehicle speed via Set Mode item "G10 UNIT SELECT" in the "SYSTEM" group (see page 42), and also change the time format via Set Mode item "I02 DATE&TIME FORMAT" in the "TIMER/CLOCK" group (see page 44). : The FGPS-2 GPS Antenna Unit requires CT-133 GPS Antenna Cable and CT-136 GPS Antenna Adapter.
24
FTM-350 SERIES OPERATING MANUAL
GPS OPERATION (REQUIRES OPTIONAL GPS ANTENNA UNIT)
"Point" memory The FTM-350 Series Transceiver has 16 "point" memories (four channels in each of four groups), which store the position (Longitude/Latitude) and the date. When your vehicle nears one of the "Point" memories, the "Nav" pop-up window will open for ten seconds even if another page is being displayed. You may customize the length of time the window opens via Set mode item "H03 NAVI POPUP" in the "NAVI" group. In addition, the "date" may be changed to a place or name, using the following procedure: 1. Rotate the left side [DIAL] knob to select the "Point" memory "date" to be changed. Press the left side [DIAL] knob to show the detail data of the "Point" memory. Press the left side [DIAL] knob again to enable editing of the stored data. Rotate the left side [DIAL] knob to toggle the point alarm function ON/OFF. [. . . ] 5 SYSTEM RESET: Resets the Set Mode item settings (except "APRS/PKT" group) to their factory defaults. 6 ALL RESET: Clears all memories and other settings to factory defaults. 7 APRS RESET: Resets only the Set Mode item setting of the "APRS/PKT" group to their factory defaults. Set the right band to a 144 MHz frequency and the left band to a 430MHz frequency (or vice versa) before beginning this procedure. [. . . ]