User manual YAESU FTM-10SR

[. . . ] VHF/UHF DUAL BAND FM TRANSCEIVER FTM-10SR OPERATING MANUAL VERTEX STANDARD CO. , LTD. VERTEX STANDARD 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A. YAESU EUROPE B. V. Box 75525, 1118 ZN Schiphol, The Netherlands Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. VERTEX STANDARD HK LTD. Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong VERTEX STANDARD (AUSTRALIA) PTY. , LTD. Normanby Business Park, Unit 14/45 Normanby Road Notting Hill 3168, Victoria, Australia Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Menu ("Set") Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] See page 87. AUTOMATIC AUDIO VOLUME CONTROLLER The FTM-10SR includes an Automatic Audio Volume Controller to allow the most comfortable and/or effective reception in noisy environments. Press and hold the [VOL/SEL] key for one second to activate the Menu mode. ON MIN: Activates the Automatic Audio Volume Controller with the low effect level. ON MID: Activates the Automatic Audio Volume Controller with the medium effect level. ON MAX: Activates the Automatic Audio Volume Controller with the high effect level. Press the [VOL/SEL] key to save the new setting and exit to normal operation. 56 FTM-10SR OPERATING MANUAL CONVENIENCE FEATURES AF-VFO FEATURE By default, the volume control (DIAL knob) and Clock display do not return to the frequency control automatically when you leave an interval of approximately three seconds. You may change the status of the DIAL knob so that the display will return automatically to the Frequency select dial function and Frequency display. Press and hold the [VOL/SEL] key for one second to activate the Menu mode. TOGGLE: Keeps the DIAL knob function and display until the [VOL/SEL] key is pressed once again. AUTOBACK: The DIAL knob function and display comes back to frequency selection and frequency display approximately three seconds after. Press the [VOL/SEL] key to save the new setting and exit to normal operation. VOX OPERATION The VOX system provides automatic transmit/receive switching based on voice input to the microphone. With the VOX system enabled, you do not need to press the PTT key in order to transmit. Press and hold the [VOL/SEL] key for one second to activate the Menu mode. Rotate the DIAL knob to select the one of the following microphone functions. R-HAND: Enable the VOX operation for the microphone which is connected to the rear panel MIC Jack. F-HAND: Enable the VOX operation for the microphone which is connected to the front panel MIC Jack. Press the [VOL/SEL] key to save the new setting and exit to normal operation. To disable the VOX operation, just repeat the above procedure, rotating the DIAL knob to select "VOX OFF" in step 4 above. If the VOX feature is activated by background noise, adjust the VOX gain via the Menu Item "F47 VOX SENS". When the transceiver audio is output to the speaker, the VOX will not activate the transmitter even if you talk directly into the microphone. FTM-10SR OPERATING MANUAL 57 CONVENIENCE FEATURES VOX SENSITIVITY You may select the VOX sensitivity. Press and hold the [VOL/SEL] key for one second to activate the Menu mode. Available selections are "NORMAL", "HIGH", and "MAX". [. . . ] If this happens, resetting of the microprocessor may restore normal operation. Rotate the DIAL knob to one of the following Reset Menu items: SF1 COPY ALL: Transfer all memories and other settings from a transceiver to another FTM-10SR. SF2 COPY MSG: Transfer all messages from a transceiver to another FTM-10SR. SF4 RSET SYS: Resets the Menu Item settings to their factory defaults. [. . . ]