User manual YAESU FT-102

[. . . ] 41 Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Cloning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 "Set" (Menu) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 INTRODUCTION The Yaesu FT-102is a deluxe, rugged FM mobile transceiver providing high power output and outstanding receiver performance for the 144 MHz Amateur band. [. . . ] Press the [MHz(SET)] key momentarily, then rotate the DIAL knob to recall the memory bank on which you wish to change a label. If you make a mistake, press the [REV(DW)] key to back-space the cursor, then re-enter the correct letter, number, or symbol. Repeat steps 4 through 6 to program the remaining letters, numbers, or symbols of the desired label. When you have programmed a name which is under 6 characters, press and hold in the [MHz(SET)] key for one second to confirm the label and exit to normal operation. FT-102OPERATING MANUAL 39 MEMORY OPERATION HOME CHANNEL MEMORY A convenient one-touch "Home" channel memory is available to simplify return to your most-often-used frequency. This memory does not appear in the regular memory bank, to simplify operation and speed recall of this important channel. To recall the Home channel, just press the [D/MR(MW)] key, repeatedly if necessary, until the "HM" icon appears on the display; this indicates that the Home USA version EXP version Channel has been recalled. The factory default frequency for the Home channel is 146. 520 MHz (USA version, EXP version: 144. 000 MHz). You can re-program the Home channel in a manner identical to that used for the regular memories: 1. From the VFO mode, tune in the frequency you wish to store, and set all repeater shifts and other data just the way you do for "normal" memory channel storage. Press and hold in the [D/MR(MW)] key for one second, then press the [REV(DW)] key to store the displayed data into the Home channel. The memory label will disappear (since you are still operating in the VFO mode). Press and hold in the [MHz(SET)] key for one second to save the new setting and exit to normal operation. FT-102OPERATING MANUAL 43 SCANNING MEMORY SKIP SCANNING When you have some continuously-active channels in memories, you may wish to skip them for scanning, but still have them available for manual selection. To mask a memory to be skipped (only) during scanning, use the following procedure: 1. Set the radio to the Memory Recall mode by pressing the [D/MR(MW)] key repeatedly, as necessary, until "MR" and a channel number appear on the right side of the display. Rotate the DIAL knob to select the Memory Channel to be skipped during scanning. Press and hold in the [MHz(SET)] key for one second, then rotate the DIAL knob to select "47 SKIP. " 4. Press the [MHz(SET)] key, then rotate the DIAL knob so as to select "SKIP". The "ONLY" selection is used for "Preferential Memory Scan, " described in the next section. Press and hold in the [MHz(SET)] key for one second to save the new setting and exit to normal operation. A "SKIP" icon will appear when you recall the "skipped" memory channel manually. To re-institute a channel into the scanning loop, select "OFF" in step 4 above, after first recalling the currently-blocked channel (the "Skipped" channel is accessible via manual channel selection methods using the DIAL knob in the Memory mode, whether or not it is locked out of the scanning loop). 44 FT-102OPERATING MANUAL SCANNING PREFERENTIAL MEMORY SCAN The FT-102also allows you to set up a "Preferential Scan List" of channels which you can "flag" within the memory system. These channels are designated by a blinking "SKIP" icon when you have selected them, one by one, for the Preferential Scan List. [. . . ] Available Values: ­RPT / + RPT / SIMP Default: SIMP 44 RVRT Function: Enables/disables the "Priority Channel Revert" feature. Available Values: ON / OFF Default: OFF 45 S SRCH Function: Selects the Smart Search Sweep mode. Available Values: SINGLE / CNTNUE Default: SINGLE SINGLE: The transceiver sweeps the current band once in each direction, starting on the current frequency. All channels where activity is present (up to 15 in each direction) are loaded into the Smart Search memories. [. . . ]