User manual XYRON 2500

[. . . ] With the Xyron 2500, documents are easily laminated or can be transformed into signs, stickers or labels instantly. The machine and supplies are compatible with all types of computer-printed media including laser, inkjet, color and thermal in a wide range of material sizes and thickness. Supply rolls for 2500 AT400-300 AT402-300 AT406-170 DL403-300 SL403-300 LAT405-300 LAT406-300 LAT409-170 Adhesive Application ­ High Tack Adhesive Application ­ Low Tack Adhesive Application ­ Repositionable Two-Sided Lamination One-Sided Lamination Combination Lamination/Adhesive Application - High Tack Combination Lamination/Adhesive Application - Low Tack Combination Lamination/Adhesive Application - Repositionable EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 Please follow the attached directions carefully. Understanding the Xyron 2500's Adhesive/Laminating System Parts and Functions Upper Idle Bar Lower Idle Bar Paddle Used to lock document in place Top Cover Removes to install/remove supplies Feed Tray Used to guide and align documents into the machine Crank Handle Used to advance documents and film thru machine Upper Supply Roll Rubber Rollers Cut Blade Used to trim output as it exits ­ the machine will cut when moved to either direction Slots for Supply Installation Upper Cut Bar Lower Cut Guide Lower Access Door Open to install and remove supplies Lower Supply Roll EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 Setting Up Remove the machine from the packaging and place on a level surface. Locate the crank handle and training video which are taped to the bottom inside of the machine. [. . . ] The document should extend past the edge of the paddle 1-2 inches (2. 5-5cm). Note: The side of the document which is face down will have adhesive applied when using Front-Side Lamination/Back-Side Permanent Adhesive Transfer. · Ensure that the leading edge of the document is adhered down evenly. If necessary slide your fingers across the leading edge to secure it in place. the document through the machine. · Turn the handle clockwise to advance · Align the document parallel to the edge of the feeder tray. Step 3: · Trim the document by pressing down on the Note: As the document exits the machine, you may wish to trim the leading edge. This will avoid a later trimming operation. blade holder and sliding it in either direction. EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 How to apply Back-Side Permanent Adhesive Transfer · Steps 1, 2 and 3. . . same as above. · Remove the protective clear mask layer and discard. · Remove the document from the white release liner when you're ready to mount it. · This process removes excess adhesive from everywhere except the back of the item run through the machine. Replacement Cartridges Product No. AT400-300 AT402-300 AT406-170 DL403-300 SL403-300 LAT405-300 Description Adhesive Application ­ High Tack Adhesive Application ­ Low Tack Adhesive Application ­ Repositionable Two-Sided Lamination One-Sided Lamination Combination Lamination/Adhesive Application ­ High Tack Combination Lamination/Adhesive Application ­ Low Tack Combination Lamination/Adhesive Application ­ Repositionable Applications Paste-ups, comps, storyboards & presentations on foam core Paste-ups, comps, storyboards & presentations on foam core Paste-ups, comps, storyboards & presentations on foam core Posters, inkjet & thermal prints & banners Indoor applications where protection of the rear side is not needed Paste-ups, comps, storyboards & presentations on foam core, provides protection to top surface Paste-ups, comps, storyboards & presentations on foam core, provides protection to top surface Feet Per Roll 300 300 170 300 300 300 LAT406-300 300 LAT409-170 Paste-ups, comps, storyboards & presentations on foam core, provides - Telefon 9633 3500 EDNord - Istedgade 37A - 9000 Aalborgprotection to top surface 170 Supply Roll Removal Step 1 -- Step 2 -- · Remove the top cover by lifting upward. · Make a small hole with a knife about one inch (2. 54cm) from the left edge of the film. Use caution to avoid cutting into the rubber rollers. · Remove the feed tray by lifting and pulling away from the machine. · Slide the knife towards the right Step 3: Step 4: · Turn the handle 1/2 turn maximum in the direction of the arrows. This step will cause the uncut film at the edges to break, creating a laminated leader for easy installation at a later time. · Remove the supply rolls from the machine. Xyron recommends that supplies are stored laying flat in a cool, dry place using the original packaging. EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 Maintenance, Safeguards & Tips When properly used, the Xyron 2500 is relatively maintenance-free. Listed below are safeguards and tips that will produce better results. Importance of a clean document: For best results when laminating, it is highly recommended that the document be cleaned with a soft, lint-free cloth immediately prior to lamination. Small dust or lint particles may cause the laminate to "tent", producing an appearance similar to a small air bubble. Cut blade replacement and cleaning: The cut blade may accumulate adhesive over time. Cleaning the blade must be done with great care to avoid personal injury. To remove the blade, slide the orange blade holder into the notch and lift upwards. Carefully remove the blade holder and replace or clean with a light solvent such as isopropyl alcohol. Use after storage: For applications where the appearance of your laminated document is critical, it is highly recommended that the Xyron 2500 be used and stored in a clean, dust-free environment. Airborne dust particles and lint will tend to adhere to the bare adhesive inside the supply roll. If the machine has not been used for several days or was subject to a dusty environment, it is recommended that four inches (10cm) of material be advanced and discarded before inserting your document. It is also recommended that the feed tray is cleaned with a lint-free cloth. Cleaning adhesive from the nip rollers: The nip rollers are designed to be self-cleaning under normal use. [. . . ] Verify supply rolls are firmly seated at base of grooves in side plates. Clean adhesive buildup from idler roller using isopropyl alcohol or Xyron Adhesive Cleaner #990. Cut Blade does not slide smoothly. Cut Blade does not cut well. Upper Blade Bar sticking in side plate groove or blade sticking on Blade Bar. Material is curled or adhesive has been transferred to the Nip Roller causing the film to stick. [. . . ]