User manual TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199. We hope that this TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199 user guide will be useful to you.
Manual abstract: user guide TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199
Detailed instructions for use are in the User's Guide.
[. . . ] TJERNLUND PRODUCTS, INC.
1601 Ninth Street · White Bear Lake, MN 55110-6794 PHONE (800) 255-4208 · (651) 426-2993 · FAX (651) 426-9547 Visit our web site · www. tjernlund. com
MODEL (950-0625) SS1 REPLACEMENT MOTOR WITH WHEEL KIT INSTRUCTIONS
Disconnect power supply before making wiring connections to prevent electrical shock and equipment damage. IMPORTANT: Motor replacement will depend on which of the three date code periods the SideShot was manufactured during. For SideShots with date codes prior to "9226", (black FASCO motor with 2 wire leads), design enhancements have made replacements of these motors obsolete. [. . . ] 8.
SideShots with a date code between "9226" and "9517", (gray MAGNETEK motor with 3 wire leads) For the steps following below, refer to diagram B. Note: Removal of plenum access cover plate will allow for removal of inlet collar nuts with 11/32" box end wrench. Push down electrical box about 1/4" so motor mount plate can clear junction box. Once motor mount plate has cleared the studs it can be rotated so motor mount plate flat aligns up with junction box for easier removal. Holding the motor, apply firm pressure towards the plenum of the SideShot and remove and save the (6) motor mount nuts. Note: An 11/32" box end wrench is used for nut directly under electrical box. Note: Hold the assembly firmly; failure to do so could damage internal parts.
DIAGRAM B
4.
5.
6.
Slide motor/wheel assembly from Plenum. Grasp only the motor casing; do not damage wheel, shaft or other components on Plenum. Do not rest assembly on wheel.
For the steps following below, refer to diagram C. Wheels "fused" to shaft may require penetrating oil and/or a wheel puller to facilitate removal. Important: The housing inlet collar from old motor will have to be removed and saved for use with the new motor.
DIAGRAM C
For the steps following below, refer to diagram D. The new motor/wheel with spring ring inlet collar assembly is only compatible with SideShots with date codes after 9518. The following modifications will have to be made to adapt the motor/wheel assembly to the SideShot with date codes between 9226 and 9517. Loosen set screw with 5/32" allen wrench and remove wheel from new motor.
DIAGRAM D
10. Remove and save (4) nuts from the new motor mounting plate and remove from motor. Remove (2) screws which hold spring ring inlet collar assembly to mounting plate and discard spring ring inlet collar assembly. [. . . ] The motor is grounded by contact with the Plenum and ground wire from terminal strip to Plenum. Remove 1/4" of insulation from the WHITE wire of motor and connect to "L2" of terminal strip. Reestablish power and run SideShot through heating cycle to verify proper operation.
P/N: 8504016
©1999 TJERNLUND PRODUCTS, INC. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199 will begin.
