User manual SMC SMCWGBR14-N2

[. . . ] USER GUIDE BARRICADETM N 802. 11n Wireless 4-port Gigabit Broadband Router SMCWGBR14-N2 BarricadeTM N SMCWGBR14-N2 User Guide No. TEL: +886 3 5770270 Fax: +886 3 5780764 September 2011 SMC-UG-0911-02 Information furnished by SMC Networks, Inc. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. [. . . ] Current PIN - The current value of the Router's PIN displayed here. The default PIN of the Router can be found in the label or User Guide. Gen New PIN - Click this button, and then you can get a new random value for the Router's PIN. Add device - You can add the new device to the existing network manually by clicking this button. 2. Add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and Router using either Push Button Configuration (PBC) method or PIN method. NOTE: To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile. For the configuration of the new device, here takes the Wireless Adapter of our company for example. By PBC: If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Press the WPS button on the front panel of the Router. ­ 64 ­ CHAPTER 6 | Wireless Settings WPS Figure 45: WPS button 2. Press and hold the WPS button of the adapter directly for 2 or 3 seconds, then the adapter will connect to the router by WPS automatically. Figure 46: WPS button Method Two: 1. Press the WPS button on the front panel of the Router. Figure 47: WPS button 2. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next. ­ 65 ­ CHAPTER 6 | Wireless Settings WPS Figure 48: The WPS Configuration Screen of Wireless Adapter 3. Click Finish to complete the WPS configuration. Figure 49: The WPS Configuration Screen of Wireless Adapter ­ 66 ­ CHAPTER 6 | Wireless Settings WPS Method Three: 1. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 50: Add a New Device 2. Choose Press the button of the new device in two minutes and click Connect. 3. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next. Figure 51: The WPS Configuration Screen of Wireless Adapter ­ 67 ­ CHAPTER 6 | Wireless Settings WPS 4. Click Finish to complete the WPS configuration. Figure 52: The WPS Configuration Screen of Wireless Adapter ­ 68 ­ CHAPTER 6 | Wireless Settings WPS By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 53: Add a New Device 2. Choose Enter the new device's PIN and enter the PIN code of the wireless adapter in the field behind PIN in the above figure. NOTE: The PIN code of the adapter is always displayed on the WPS configuration screen. 3. For the configuration of the wireless adapter, please choose Enter a PIN into my access point or a registrar in the configuration utility of the WPS as below, and click Next. ­ 69 ­ CHAPTER 6 | Wireless Settings WPS Figure 54: The WPS Configuration Screen of Wireless Adapter NOTE: In this example, the default PIN code of this adapter is 26499123 as the above figure shown. For the configuration of the wireless adapter, please choose Enter a PIN from my access point in the configuration utility of the WPS as below, and enter the PIN code of the Router into the field behind Access Point PIN. [. . . ] Type the Router's LAN IP address (the default IP is 192. 168. 2. 1) into the Default gateway field. 4. In the Preferred DNS Server field you can type the DNS server IP address, which has been provided by your ISP. Figure 120: Use the Following IP ­ 127 ­ C HARDWARE SPECIFICATIONS STANDARDS IEEE 802. 3 10BASE-T IEEE 802. 3u 100BASE-TX IEEE 802. 3ab 1000BASE-T 802. 11b 802. 11g 802. 11n PROTOCOL TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP NUMBER OF PORTS 1 10/100/1000 Mbps Auto-Negotiation WAN RJ-45 port 4 10/100/1000 Mbps Auto-Negotiation LAN RJ-45 ports supporting Auto MDI/MDIX 1 USB 2. 0 port CABLING TYPE 10BASE-T: UTP Category 3, 4, 5 cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) 100BASE-TX: UTP Category 5, 5e cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) 1000BASE-TX: UTP Category 5e, 6 cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) LED INDICATORS Power, System, WLAN, WAN, LAN (1-4), USB, WPS FREQUENCY BAND 2. 4 ~ 2. 4835 GHz RADIO DATA RATE 11b: 11/5. 5/2/1M (Automatic) 11g: 54/48/36/24/18/12/9/6M (Automatic) 11n: up to 300 Mbps (Automatic) CHANNELS 13 FREQUENCY EXPANSION DSSS (Direct Sequence Spread Spectrum) ­ 128 ­ APPENDIX C | Hardware Specifications MODULATION DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM SECURITY WEP/WPA/WPA2/WPA2-PSK/WPA-PSK SENSITIVITY @PER 270M: -68dBm@10% PER; 130M: -68dBm@10% PER 108M: -68dBm@10% PER; 54M: -68dBm@10% PER 11M: -85dBm@8% PER; 6M: -88dBm@10% PER 1M: -90dBm@8% PER RF POWER 20dBm (max EIRP) ANTENNA GAIN 3dBi*3 TEMPERATURE Operating: 0 °C to 40 °C (32 to 104 °F) Storage: -40 °C to 70 °C (-40 to 158 °F) HUMIDITY Operating: 10% to 90% (non-condensing) Storge: 5%-90% (non-condensing) ­ 129 ­ GLOSSARY IEEE 802. 11B A wireless standard that supports wireless communications in the 2. 4 GHz band using Direct Sequence Spread Spectrum (DSSS). The standard provides for data rates of 1, 2, 5. 5, and 11 Mbps. IEEE 802. 11G A wireless standard that supports wireless communications in the 2. 4 GHz band using Orthogonal Frequency Division Multiplexing (OFDM). The standard provides for data rates of 6, 9, 12, 18, 24, 36, 48, 54 Mbps. [. . . ]