User manual SMC 7904BRA2

[. . . ] Router with built-in ADSL2/2+ Modem From SMC's line of award-winning connectivity solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 August 2006 R. 01 F/W 0. 11 Information furnished is believed to be accurate and reliable. However, no responsibility is assumed by our company for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of our company. We reserve the right to change specifications at any time without notice. [. . . ] Go to "Confirm" on page 4-14 in the manual for details about the settings. 4-12 SETUP WIZARD 1483 Routing (DHCP) Parameter DNS Server VPI/VCI Encapsulation Description Enter the DNS Server IP address provided by your ISP. Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Select the encapsulation used by ISP from the drop down menu. Click NEXT to continue to the "Confirm" settings screen. Go to "Confirm" on page 4-14 in the manual for details about the settings. 4-13 CONFIGURING THE BARRICADETM Confirm The Confirm screen shows a summary of the configuration parameters. Check ADSL operation mode (WAN), Network Layer Parameters (WAN) and ISP parameters are correct. Parameter ISP Protocol VPI/VCI Description The name of the ISP you have selected from list. If you are unsure if the selected protocol is correct check with your ISP. If you are unsure the VPI/VCI values are correct check with your ISP. ADSL Operation Mode (WAN) AAL5 Encapsulation Shows the packet encapsulation type. If you are unsure the selected Encapsulation is correct check with your ISP. Network Layer Parameters (WAN) IP Address Subnet Mask Default Gateway WAN IP address (only displayed if you have static IP). WAN gateway (only displayed if you have static IP). 4-14 SETUP WIZARD Parameter DNS Server Description The IP address of the DNS server. If the DNS address field was left blank in previous steps the address will be displayed as 0. 0. 0. 0. The password (hidden). ISP Parameters Username Password If the parameters are correct, click FINISH to save these settings. Go to "Troubleshooting" on page A-1 if you cannot make a connection to the Internet. 4-15 CONFIGURING THE BARRICADETM Configuration parameters There are 13 main menu items located on the left side of the screen. Each main menu item is described in the following table. Menu System Description Sets the local time zone, the password for administrator access, and the IP address of a PC that will be allowed to manage the Barricade remotely. Sets the TCP/IP configuration for the Barricade LAN interface and DHCP clients. Configures a variety of security and specialized functions including: Access Control, URL blocking, Internet access control scheduling, intruder detection, and DMZ. Sets the ADSL operation type and shows the ADSL status. WAN LAN NAT Routing Firewall SNMP UPnP QoS ADSL 4-16 CONFIGURATION PARAMETERS Menu DDNS Tools Description Configures Dynamic DNS function. Contains options to backup & restore the current configuration, restore all configuration settings to the factory defaults, update system firmware, or reset the system. Provides WAN connection type and status, firmware and hardware version numbers, system IP settings, as well as DHCP, NAT, and firewall information. Displays the number of attached clients, the firmware versions, the physical MAC address for each media interface, and the hardware version and serial number. Shows the security and DHCP client log. Status 4-17 CONFIGURING THE BARRICADETM SYSTEM Time Settings Select your local time zone from the drop down menu. This information is used for log entries and client filtering. For accurate timing of log entries and system events, you need to set the time zone. If daylight savings is used in your area, check the box to enable the function, and select the start/end dates. [. . . ] Check the adapter on the attached device and cable connections for possible defects. Action · Network Connection Problems Cannot ping the Barricade from the attached LAN · Verify that the IP addresses are properly configured. For most applications, you should use the Barricade's DHCP function to dynamically assign IP addresses to hosts on the attached LAN. However, if you manually configure IP addresses on the LAN, verify that the same network address (network component of the IP address) and subnet mask are used for both the Barricade and any attached LAN devices. [. . . ]