User manual SMC 7004AWBR

[. . . ] Link status 1~3 Blinking SPEED 1~3 Data Rate Green On Port 1-3 DC IN 2. 2 Procedure for Hardware Installation 1. Decide Where to Place Your Wireless Broadband Router: You can place your Wireless Broadband Router on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your Wireless Broadband Router in the center of your office (or your home) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. Wired LAN connection: connect an Ethernet cable from your computer's Ethernet port to one of the LAN ports of this product. [. . . ] In the "Internet Options" window click the "Connections" tab. In the "Preferences" window, under "Category" double-click "Advanced", then click "Proxies". Select "Direct connection to the internet. " Click "OK. " English iii. Clear all the checkboxes and click "OK. " Click "OK" again to close the "Internet Options" window. 13. Repeat these steps for each computer connected to your Barricade. English Configuring Your Barricade If you connect to the Internet using a: Cable Modem, turn to page 13 DSL Modem, turn to page 15 DSL Modem with a Log In name and Password, turn to page 17 b. Click "Edit", then click "Preferences. . . " Configuring Your Barricade for a Cable Modem 1. In the "Location" field (for Netscape) or "Address" field (for Internet Explorer), type "http://192. 168. 123. 254" and press <ENTER>. In the "System Status" page of the Barricade web console, type your password in the "System Password" field (default is "admin") and click the "Log In" button. 5. Under "WAN Type" Click the "Change. . . " button. 6. Select "Dynamic IP Address" and click the "Save" button. English English 7. Key in your "Host Name" if your Internet Service Provider has given you one (i. e. When prompted to reboot now, click "OK. " 10. Once the Barricade is rebooted, you can surf the Internet as you normally would from all computers connected to it. 4. Click "Primary Setup" Configuring Your Barricade for a DSL Modem 1. Select "Static IP Address" and click the "Save" button. 2. In the "Location" field (for Netscape) or "Address" field (for Internet Explorer), type "http://192. 168. 123. 254" and press <ENTER>. In the spaces provided, key in the values provided to you by your ISP. (Note: Enter the IP Address given to you in the "WAN IP Address" field, not the "LAN IP Address" field. ) 3. In the "System Status" page of the Barricade web console, type your password in the "System Password" field (default is "admin") and click the "Log In" button. English English 4. Click "Save", and then click the "Reboot" button. 9. Under "WAN Type" Click the "Change. . . " button. 10. Once the Barricade is rebooted, you can surf the Internet as you normally would from all computers connected to it. Configuring Your Barricade for a DSL Modem with a Log-In Name and Password 1. In the "Location" field (for Netscape) or "Address" field (for Internet Explorer), type "http://192. 168. 123. 254" and press <ENTER>. In the "System Status" page of the Barricade web console, type your password in the "System Password" field (default is "admin") and click the "Log In" button. 6. [. . . ] In the "System Status" page of the Barricade web console, type your password in the "System Password" field (default is "admin") and click the "Log In" button. D. If you use DSL, you may need to reconfigure your Barricade for a PPPoE connection (Point to Point Protocol over Ethernet). To reconfigure, go to the section labeled "Configuring Your Barricade for a DSL Connection with a Log-In Name and Password" on page 19. Time Warner or Road Runner in some areas) you may need to shut down and restart your cable modem after you've finished configuring the Barricade. 5. [. . . ]