User manual SMC 7003-PCI

[. . . ] DESCRIPTION OF HARDWARE DESCRIPTION OF HARDWARE The SMC7003-PCI is a cost effective, controller less ADSL solution that requires minimal external components. (Only one external line driver is needed in the analog front-end circuit). The SMC7003-PCI achieves transmission rates of up to 8Mbps downstream and 768Kbps upstream over existing copper wire. The SMC7003-PCI designed to meet ANSI T1. 413 Issue 2, ITU G. dmt and G. lite requirements with both splitter and splitterless operations. [. . . ] Your ADSL Internet connection is established! 22 INSTALLING THE SMC7003-PCI Making an ADSL connection RFC 2364 - Point-to-Point Protocol over ATM ­ 2000 1. Double-click on the SMCA PPPoA icon that appears on your desktop. 2. The Connect My Connection window will appear. Enter your User Name and Password supplied by your ADSL service provider. Click Dial . 3. The Connection complete window appears, click O K. 23 INSTALLING THE SMC7003-PCI Windows NT4. 0 RFC 1483 ­ Bridged Ethernet over ATM RFC 1577 - CLASSICAL INTERNET PROTOCOL OVER ATM 1. On your desktop, double-click My Computer, and then double-click Control Panel . Insert SMC Universal CD into your systems CD drive. 5. The Insert Disk window appears. Click Brow se to locate the driver on your CD- ROM for the protocol supported by your ADSL provider: 1483NT4 or 1577NT4 (The example uses "d" as the CD-ROM drive letter. Your drive may have a different letter. ) Click O K. 6. The Select OEM Option window will find the SMC ADSL PCI NIC, Click O K. 24 INSTALLING THE SMC7003-PCI 7. Click the Adapters tab to verify that the SMC ADSL PCI NIC has been found. Click on the Protocols tab and verify that the ADSL Management and Monitor Interface is present. NOTE: To review the Network window properties at any time, right-click the Network Neighborhood icon and select Properties. NOTE: If no previous network devices have been installed, then the Network Neighborhood icon will not be present on your desktop. To open the Network window, double-click My Computer then Control Panel then Network. 8. The Microsoft TCP/IP Properties window appears. Enter in the IP Address, Subnet Mask and Default Gateway supplied by your ADSL service provider. Go to page 26. 25 INSTALLING THE SMC7003-PCI WINDOWS NT 4. 0 SETTING THE ADSL CONFIGURATION FOR RFC 1483 OR RFC 1577 1. After your PC has rebooted, right-click on the Mapi Icon, and select the Configuration option. 2. The Configuration window appears. Enter in the VPI, VCI, and Framing values supplied by your ADSL service provider. 3. In the Select ADSL Mode section, select the mode(s) recommended by your ADSL service provider. Click on the mode(s) required and then click on Settings. NOTE: The service mode type will be one of the following: q q q ANSI T1. 413 Issue 2 ITU G. 992. 2 Annex A (G. lite) ITU G. 992. 1 Annex A (G. dmt) 4. The PVC Setup window appears. Click Yes to restart your PC system and to allow the new changes to take effect. 5. Now you must create a Dial- up Connection. Please go to page 30. 26 INSTALLING THE SMC7003-PCI WINDOWS NT4. 0 RFC 2364 ­ Point to Point Protocol over ATM 1. On your desktop, double-click My double-click Control Panel . Computer, and then 2. In the Control Panel window, double-click the Network icon. Select the Adapters tab and then click Add. 3. The Select Network Adapter window appears. Click Have Disk . 4. Insert the ADSL Driver CD- ROM into your systems CD drive. 5. The Insert Disk window appears. Click Browse to locate the driver on your CD -ROM for the protocol supported by your ADSL provider: 2364NT4 (The example uses "d" as the CD- ROM drive letter. Your drive may have a different letter. ) Click O K. 6. The Select OEM Option window will find the SMC ADSL PCI NIC, Click O K. 7. The Setup Message window appears. Insert your NT4. 0 CD-ROM into the PC system CD drive, and type in "D:\i386" Click Continue. 27 INSTALLING THE SMC7003-PCI 9. The Add RAS Device window appears. [. . . ] As a measure of packet transfer performance, the Packet Errors are counted and tracked against the total number of Packets Received. Click Run Diagnostics to run the diagnostic program that will test PC functionality and report the status. A warning message pops up that the ADSL service will disconnect before performing the diagnostic test. If connected to the Internet at this time, disconnect any Dial- up sessions. [. . . ]