User manual SMC 2804WBRP-G

[. . . ] BarricadeTM g 2. 4 GHz 54 Mbps Wireless Cable/DSL Broadband Router From SMC's Barricade line of Broadband Routers 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 October 2003 Pub No: 149100026900ER01 COPYRIGHT Information furnished by SMC Networks, Inc. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. [. . . ] With Universal Plug and Play, a device can automatically and dynamically join a network, obtain an IP address, communicate its capabilities, and learn about the presence and capabilities of other devices. Contains options to back up & restore the current configuration, restore all configuration settings to the factory defaults, update system firmware, or reset the system. Provides WAN connection type and status, firmware and hardware version numbers, system IP settings, as well as DHCP, NAT, and Firewall information. Displays the number of attached clients, the firmware versions, the physical MAC address for each media interface, and the hardware version and serial number. Shows the security and DHCP client log. Tools Status 34 ADVANCED SETUP SYSTEM Time Zone Set the time zone and time server for the Router. Check Enable Automatic Time Server Maintenance to automatically maintain the Router's system time by synchronizing with a public time server over the Internet. Then configure two different time servers by selecting the options in the Primary Server and Secondary Server fields. 35 Configuring the Wireless Barricade g Router Password Settings Use this menu to restrict access based on a password. For security you should assign one before exposing the Router to the Internet. Passwords can contain from 3­12 alphanumeric characters and are not case sensitive. Note: If your password is lost, or you cannot gain access to the user interface, press the Reset button on the rear panel (holding it down for at least five seconds) to restore the factory defaults. (The default password is smcadmin. ) Enter a maximum Idle Time Out (in minutes) to define a maximum period of time for which the login session is maintained during inactivity. If the connection is inactive for longer than the maximum idle time, it will perform system logout, and you have to log into the web management system again. (Default: 10 minutes) 36 ADVANCED SETUP Remote Management Remote Management allows a remote PC to configure, manage, and monitor the Router using a standard web browser. Note: If you specify 0. 0. 0. 0 as this IP address, any host can manage the Router. Syslog Server The Syslog Server tool will automatically download the Barricade log to the server IP address specified by the user. Enter the Server LAN IP Address and check the Enabled box to enable this function. 37 Configuring the Wireless Barricade g Router WAN Specify the WAN connection type provided by your Internet Service Provider, then click More Configuration to enter detailed configuration parameters for the selected connection type. 38 ADVANCED SETUP Dynamic IP The Host Name is optional, but may be required by some ISPs. The default MAC address is set to the WAN's physical interface on the Router. Use this address when registering for Internet service, and do not change it unless required by your ISP. If your ISP used the MAC address of an Ethernet card as an identifier when first setting up your broadband account, only connect the PC with the registered MAC address to the Router and click the Clone MAC Address button. This will replace the current Router MAC address with the already registered Ethernet card MAC address. If you are unsure of which PC was originally set up by the broadband technician, call your ISP and request that they register a new MAC address for your account. Register the default MAC address of the Router. 39 Configuring the Wireless Barricade g Router Point-to-Point Over Ethernet (PPPoE) Enter the PPPoE User Name and Password assigned by your Service Provider. The Service Name is normally optional, but may be required by some service providers. [. . . ] This will verify that you have successfully set up your LPR printing port, and now you can print through the SMC Barricade Router. Confirm printer connection On the status page of the web-based log in, you can confirm the printer connection to the Barricade Router. OK 93 Configuring Printer Services Printer Server Setup in Linux Systems 1. In GNome mode, type "printconf-gui" to open the printconf-gui window. Type the printer name as "lpt1" and select Local Printer in the Queue Type field. [. . . ]