User manual SMC 2655W

[. . . ] TM Wireless Access Point N Protocol-independent networking functionality N 11 Mbps data rate per channel: provides an alternative to wired LANs that can dramatically cut costs N Coverage area 180 m (590 ft) at 11 Mbps, 550 m (1800 ft) at 1 Mbps N Seamless connectivity to wired Ethernet LANs augments existing networks quickly and easily N Direct Sequence Spread-Spectrum (DSSS) technology provides robust and secure wireless connection N Easy installation N Dual dipole antenna User Guide SMC2655W EZ Connect Wireless Access Point User Guide From SMC's EZ line of low-cost workgroup LAN solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 February 2002 Pub #: 150000003500E R02 Part Number: 01-111322-006 Copyright Information furnished by SMC Networks, Inc. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. [. . . ] Just attach the access point anywhere along your Ethernet LAN to provide wireless stations within its area of coverage with transparent access to the local wired and wireless LAN. The EZ Connect Wireless Access Point supports an 11 Mbps half-duplex connection to Ethernet networks for each active channel. It is fully compliant with 2. 4 GHz DSSS CSMA/CA wireless networking as defined in the IEEE 802. 11b standard. Power Connector RJ-45 Port Applications EZ Connect wireless products offer a fast, reliable, cost-effective solution for wireless Ethernet client access to the network in applications such as: · · Remote access to corporate network information E-mail, file transfer, and terminal emulation Difficult-to-wire environments Historical or old buildings, asbestos installations, and open areas where wiring is difficult to employ 3 HARDWARE DESCRIPTION · Frequently changing environments Retailers, manufacturers, and banks which frequently rearrange the workplace or change locations Temporary LANs for special projects or peak periods Trade shows, exhibitions, and construction sites that need a temporary setup. Retailers, airline, and shipping companies that need additional workstations for peak periods. Auditors who require workgroups at customer sites Access to databases for mobile workers Doctors, nurses, retailers, or white-collar workers who need access to databases while being mobile in a hospital, retail store, in an office, or on a campus SOHO users SOHO (Small Office and Home Office) users who need easy and quick installation of a small computer network · · · 4 LED INDICATORS LED Indicators The EZ Connect Wireless Access Point includes three status LED indicators, as described in the following figure and table. LED Power (PWR) Wireless Link TX RX Ethernet LNK ACT Status On (Red) Flashing (Green) Flashing (Green) On (Orange) Flashing (Orange) Description Power is being supplied. The Access Point is transmitting or receiving data on the Ethernet LAN System Requirements Before you install the EZ Connect Wireless Access Point, be sure you have met the following requirements: · · · An AC power outlet (100~240 V, 50~60 Hz) An available RJ-45 (UTP) port on an Ethernet hub or switch 802. 11b compliant wireless Ethernet adapters with TCP/IP protocols installed 5 HARDWARE INSTALLATION 1. Select the Site ­ Choose a location for your SMC2655W Wireless Access Point. Usually, the best location is at the center of your wireless coverage area, if possible within line-of-sight of all wireless devices. Normally, the higher you place the antenna, the better the performance. For more effective coverage, position one antenna along the vertical axis and the other antenna along the horizontal axis (the antennas emit signals along the toroidal plane - and thus provide more effective coverage when positioned along alternate axis). Connect the Ethernet cable ­ The SMC2655W can be wired to an Ethernet network through an Ethernet device such as a hub or a switch using category 3, 4, or 5 UTP Ethernet cable and an RJ-45 connector. Connect the power cable ­ Connect the power adapter cable to the 9 VDC power socket on the rear panel. Warning: Use only the power adapter supplied with the SMC2655W. 6 EZ CONNECTTM SMCPWR-INJ POWER INJECTOR The SMCPWR-INJ* Power Injector allows the SMC2655W Access Point to receive power from the connected Ethernet hub or switch and is used with an Access Point that does not have access to a standard power outlet. Connect an Ethernet cable from your Ethernet hub/switch to the network port on the Power Injector. Connect another Ethernet cable from the Access Point port on the Power Injector to your Access Point. *Sold separately Note: The SMCPWR-INJ is designed for use with the SMC2655W Access Point only. Using the Power Injector with any other Ethernet device may damage the device. 7 SYSTEM CONFIGURATION Your SMC2655W is a plug and Play device. The SMC2655W Access Point includes an SNMP agent that is accessible through an SNMP manager application (EZ Connect Wireless AP Manager. ) The SNMP agent supports read-write and read-only modes. The diskette labeled "Utility Diskette" contains a utility program for the EZ Connect Wireless Access Point. The latest version may be downloaded from the download site specified on the back cover of this manual. Warning: Back up your utility diskette and use the copy as the working diskette to protect the original from accidental damage. Install and run the utility program as described in the following section. 8 UTILITY INSTALLATION (98/ME/NT/2000) Utility Installation (98/Me/NT/2000) 1. [. . . ] If you have any questions or comments regarding the features or performance of this product, or if you would like information regarding our full line of wireless products, visit us on the Web at www. smc. com or call us toll-free at 800. SMC. 4YOU. SMC Networks stands behind this and every product we sell with a 30-day satisfaction guarantee and with a limited-lifetime warranty. SMC 802. 11b Wireless Products Maximum Distance Table Speed and Distance Ranges Environmental Condition Open Environment: A line-of-sight environment with no interference or obstruction between AP/ Bridge and users. Semi-Open Environment: An environment with no major obstructions such as walls or privacy cubicles between the AP and users. Closed Environment: A typical office or home environment with floor to ceiling obstructions between the AP and users. [. . . ]