User manual SMC 2622W-U

[. . . ] EZ ConnectTM Wireless Print Server User Guide SMC2622W-P SMC2622W-U Table of Contents Chapter 1 Introduction: page 3 Features Package Contents Models LED indicators Diagnostic Push Button LAN Installation: page 8 Print Server Configuration: page 10 Overview Using the Windows Wizard Alternatives to the Windows Wizard Wireless Configuration Advanced Configuration and Management Client PC Configuration: page 18 Overview Windows Peer-to-Peer Print Driver Windows SMB Printing Windows with Server-based Print Queues Macintosh (AppleTalk) BiAdmin Management Utility: page 29 Requirements Installation Operation Web Interface Setup: page 37 Overview Preparation Connecting to the Print Server Configuration Screens Special Features: page 47 Overview Internet Printing Protocol (IPP) Internet Mail Printing SNMP Chapter 2 Chapter 3 English 1 Chapter 4 Chapter 5 Chapter 6 Chapter 7 Chapter 8 Troubleshooting: page 62 Overview Hardware & LAN Problems AppleTalk (Macintosh) Windows Printing Problems Specifications: page 71 General Specifications Regulatory Approvals Safety Instructions Wireless PCMCIA Adapter Installation: page 74 Network Server Configuration: page 77 Windows NT Server Windows 2000 Server Unix Systems Contact SMC & Warranty Information Appendix A Appendix B Appendix C English 2 Chapter 1: Introduction Features Congratulations on the purchase of your new Print Server. This device was designed to provide a simple and efficient network printing solution. The Print Server supports TCP/IP, SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI. For initial configuration, a number of utility programs are supplied to simplify setup. [. . . ] The settings on this screen must match the other Wireless stations in order for communication to occur. English Configuration Regulatory Domain Station name SSID(ESSID) Channel No. It is illegal to use this device in any location outside of the regulatory domain. On your PC, some Wireless status screens may display this name as the Access Point in use. If you experience lost connections and/or slow data transfers you may need to experiment with different channels to see which is the best. 44 Network Type Link Info Button WEP Data Privacy Off 64 Bit Encryption Select the correct value for your Wireless LAN. · 802. 11 Ad-hoc mode is used when there is no Wireless Access Point, and each Wireless station communicates directly with other Wireless stations. · Ad-hoc mode is used when there is no Wireless Access Point, and each Wireless station communicates directly with other Wireless stations. · Infrastructure mode is used when each Wireless station connects to the Wireless Access point. If selected, data is encrypted, using the default key, before being transmitted. The receiving station must be set to 64 Bit Encryption, and have the same Key value in the same position in its key table. Transmitted data is ALWAYS encrypted using the Default Key; the other Keys are for decryption only. All stations, including this Access Point, always transmit data encrypted using their default key. The receiving station will use the key number (1, 2, 3, 4) to determine which key value to use for decryption. If the key value does not match the transmitting station, decryption will fail. The easiest way to ensure there are no problems is to have every Station, including the Access Point, use the same key table (all entries identical). If selected, data is encrypted using the key before being transmitted. The receiving station must be set to use 128 Bit Encryption, and have the same Key value. Other stations must have the same key Options are "Open System" or "Shared Key". Check your Wireless card's documentation to determine the correct value. Ensure that all Wireless stations use the same setting as the Access Point. English 128 Bit Encryption WEP Authentication 45 Other Screens Server Status This screen shows server system data and the current settings for all of the other screens. For each port, the following data is listed: · Connected Printer - the model name of the printer connected to the port, if the printer name is known. (If the printer is not bidirectional, this information is unavailable. ) · Status - the current status of the printer (On-line, Off-line, Out of paper) · Printing Information - this will show either Idle or Printing. For each Logical Printer, the following fields are available: Logical Printer (Port) Select the Logical Printer Port you wish to configure. (L1 to L3 or L1 to L8, depending on your model) Click the Get Data button to update the display with the current data for the selected logical printer. [. . . ] Registration can be accomplished via the enclosed product registration card or online via the SMC web site. The Limited Lifetime warranty covers a product during the Life of that Product, which is defined as a period of 5 years from the date of purchase of the product from SMC or its authorized reseller. 80 English Replacement products may be either new or reconditioned. Any replaced or repaired product carries, either a 30-day limited warranty or the remainder of the initial warranty, whichever is longer. [. . . ]