User manual SINGER 71-30 TO 70-47

[. . . ] Pass the thread from the spooi around bobbin tension stud 3, wind it around the bobbin a few times and push the bobbin to the right for winding. Re engage the mechanism. 4 Inserting the bobbin Insert the filled bobbin in the bobbin case so that the thread unreels towards the back (G). Then draw the thread into slot H and under the spring into eye I. Inserting the bobbin case Pull up latch I and push the bobbin case onto stud B as far as it will go. Stud G and latch I must be flush. 5 Upper threading Raise the sewing foot and the take-up lever. [. . . ] Pull the thread from the spool through thread guiding hook 3, thread guide 2 and from the right into needle thread tension 19. Pass the thread around the tension stud and pull it slightly to the right behind guide G. Draw the thread from the right through take-up lever 1 and pull it through guide H. Threading the needle Thread the needle from front to back. 6 Drawing up the bobbin thread Hold the needle thread a little taut. Turn hand wheel 9 toward you until the needle moves down and up again and the take-up lever is up. Pull the bobbin thread out of the needle hole and lay both threads toward the left and back under the sewing foot. Presser bar litter Lever 20 has three positions. (Before you remove the work, turn the balance wheel forward to raise the needle and take-up lever 1. ) H = The sewing foot is lowered for sewing. Position I is marked by a notch. 7- E_ N I 7 Thread cutter (G) The thread cutter is an oblique slot bar. Draw r slot and pull them threads into the cutte downwards to cut them. Regulating the stitch length the The stitch length is set at mark G on th control. H shows how to set the stitc for sewing stretch stitches on control models 806 and 807. /- N 7 \ 8 cr< _40 o CD N (CD < -- QN CD 0Ocl) CD £ tT CD CD D3 --1 0. 0 CX) -- t3- CD T CD (0 CD 0 a g o. OlD a o. 0 OlD CD' 00. 0<D2. = 0 CD 0 . . Hole K and screw that stud H fits in slot darning foot J are used for attaching the L serves to and the edge guide. presser bar 14 Sewing feet G Normal sewing foot H Clear-VieW foot i Buttonhole foot J Hemmer foot (special accessory available from your Pfaff dealer) K L M N Zipper foot BlindstitCh foot Darning foot Guide 98-694 404-00 93-031 91 M 93-03 5 960-91 N 98-802 422-00 1I5 Special sewing feet G Zipper foot Insert the rear pin in groove I, and the front pin in groove J. The zipper foot can be adjusted sideways for stitching along the right or left zipper chain. Insert the pin of the foot in hole K and attach the foot so that it rests against its stop. Tighten screw L. Buttonhole settings On models 802 to 807 set utilitystitch dial 5 to B. Set the stitch density in the buttonhole sector of stitch length control 11. J): place it over the rear lug of the foot, pull it taut and clamp it in front lug K. This determines the buttonhole length. 16 a) . 0 0) -- Ct) CC) 4 --: 0) > . 00) -- - 0 E >, a) -- :5> a) S. ; C - 0) 0 0) tJ C a) = 0 a) . 3 = . g . 5 Z :3 a) ci) --a) (0. 0 (0 1) a) a). 0 0 > C D) 0> >Q CC) C `U a) > 3--4i 0 U) c" 03 CC) - E :5 ci :300 (0 U) 00) C1) - 4 -a) -- -C C o :3 >-. Ccii a) . 0 . 0 -- 0) . 0 a) a)a) -- (0 a) ` 0) 03 - . 5 E +. ` C 0 0. -- -- o C') :3 a)) a) = a) --- 0 -- C ±CI) -- ? 0 . a)j o'2 C -- G) . c C DO . 0 o . 22-o 5 CC) C -- C 0 g `-- E >-z >0)0)> 0 C C `2 > a) (i)cL-- `t) -0 > _s > C a) 0 a) 00 a) a) CI) C - aS 55 55 55 cc) _5 -- as -- a) C I e c') Fitting the detachable workplate on models 800, 802 and 806 The foot control receptacle of these models also serves as a detachable workplate. [. . . ] a)j o'2 C -- G) . c C DO . 0 o . 22-o 5 CC) C -- C 0 g `-- E >-z >0)0)> 0 C C `2 > a) (i)cL-- `t) -0 > _s > C a) 0 a) 00 a) a) CI) C - aS 55 55 55 cc) _5 -- as -- a) C I e c') Fitting the detachable workplate on models 800, 802 and 806 The foot control receptacle of these models also serves as a detachable workplate. Turn the receptacle round and fit it to the machine so that its two haoks enter the two holes in the machine base. G and H below left. ) Fitting the detachable workplate on models 601, 803 and 807 Push the workplate over the free arm until its two guide pins enter the holes provided. To remove the workplate reverse this proced ure. 4HJ ilHIl \ . . . . . 18 Changing the light bulb t to the Switch off the electric curren the plug. [. . . ]