User manual SILVERCREST SEKU 2000 A1

[. . . ] IMPORTANT A warning of this danger level signifies possible property damage. NOTICE A notice signifies additional information that assists in the handling of the appliance. Intended use This appliance is intended for the heating of enclosed living spaces. In addition, artificial fire flares can be created with the appliance to optically replicate an open-hearth fire. This appliance is not intended for any other use or for uses other than those mentioned. [. . . ] Dispose of packaging material that is no longer needed according to the regionally established regulations. NOTICE If possible preserve the appliance's original packaging during the warranty period so that in the case of a warranty claim you can package the appliance properly for return. SEKU 2000 A1 5 Setting up and connecting Installation requirements For the safe and correct operation of the appliance, the installation site must satisfy the following requirements: GB IE The appliance must be placed on a firm, flat and horizontal surface. Do not place the appliance in a hot, wet or very humid environment or close to inflammable materials. The mains power socket must be easily accessible at all times, thus enabling the plug to be immediately withdrawn should an emergency situation arise. Ambient temperature range: +5 to +45 °C Humidity (No condensation): 5 - 90 % DANGER Fire hazard due to material contact!If the heater makes contact with flammable materials, there is a risk of fire!Pay heed to the following safety information to avoid these fire risks: Keep inflammable materials well away from the place of installation of the appliance. Do not cover the warm air outlet openings of the appliance. Before the first use Remove all packaging materials and transport restraints from the appliance. NOTICE When you first use it, it may temporarily generate a light odour. This is normal and completely harmless. Electrical connection For a safe and correct operation of the appliance, take note of the following instructions regarding the electrical connection: Before you connect the appliance, compare the connection data (voltage and frequency) on the plate with that of your electricity supplier. Ensure that the power cable is undamaged and that it is not placed over hot surfaces and/or sharp edges. The connecting cable must not be taut. 6 SEKU 2000 A1 Operating components Operating components NOTICE The operating elements are on the front of the appliance, above right and behind the ventilation grille. To operate them, fold the ventilation grille forward. GB IE 4 3 2 5 2 3 4 5 ON/OFF switch (Flames) ON/OFF switch (Heating, level 1) ON/OFF switch (Heating, level 2) Temperature control (Thermostat) Dimmer (for flame lamps) SEKU 2000 A1 7 Set up GB IE Set up Before the appliance can be set up, the fire surround must be assembled. NOTICE Check the contents to make sure everything is there and for visible damage. Turn the adapter sleeves with the screwdriver so that the arrows on the adapter sleeves each point to the outer edge of the centre front panel 5 . Insert four double locking pins C in the upper holes on the front sides of the panel and turn the adapter sleeves E with the screwdriver to the right until the locking pins are firmly secured. C C E 5 Step 4 Now connect the so prepared centre front panel E 5 with the side panels prepared in steps 1 and 2. For this, insert two adapter sleeves in the large holes in the side panels. Turn the adapter sleeves E with the screwdriver so that the arrows on the adapter sleeves each point to the outer edge of the side panels. Then, guide each of the double locking pins in the edges of the side panels. C of the centre front panel 5 5 into the corresponding holes When done, turn all four adapter sleeves E in the centre front panel until all parts are at right angles to each other and firmly tightened. with the screwdriver to the right, E E 5 SEKU 2000 A1 11 Assembly Step 5 GB IE Place the floor plate 7 on the floor. Now take the previously assembled unit and carefully place it on the floor plate as shown in the following diagramme. Then screw together the assembled unit with the connection blocks 8 screws of the type A . For this, use G G A A Step 6 Take the top covering panel 3 and place it on the preassembled unit. 3 Secure the top covering panel from the inner side of the unit with 7 screws of the type A. 3 A 12 SEKU 2000 A1 Assembly Step 7 Take the base plate 6 and insert 4 wood plugs 6 B 7 into the holes of the plate underside. so that the four wood plugs fit into the four holes in Then place the base plate the floor plate. on the floor plate GB IE Rear view Front View 6 B 7 B Installing the appliance in the fire surround To finalise, install the appliance in the assembled fire surround. Place the appliance carefully on the base plate (from the rear of the fire surround) and then push it gently forward as far as it will go into the opening of the fire surround. Secure the appliance to the fire surround at the edges with the fixing devices 6 x 25 mm A . Insert the plug into the mains power socket. F and the screws F A WARNING Improper laying of the power cable can cause damage to people and property! [. . . ] The appliance has been manufactured with care and meticulously examined before delivery. In the case of a warranty claim, please make contact by telephone with our Service Department. NOTICE The warranty is valid only for material or manufacturing defects not, however, for transport damage, wear and tear or for damage to breakable parts, i. e. This product is for private use only and is not intended for commercial applications. [. . . ]