User manual SILVERCREST KH 700

[. . . ] After the appliance has run for this period it must be switched off until the motor has cooled itself down. 4. Safety instructions · Please read all safety instructions carefully. · Make sure that the power cord never becomes wet or damp during operation. · Arrange for defective power plugs and/or cables to be replaced as soon as possible by a qualified technician or by our Customer Service Department to avoid the risk of injury. [. . . ] · Fit the cutting blade z on the retainer r and place the latter on the drive shaft 8. 7. Working with the mixing bowl The supplied accessories for the mixing bowl 9 consist of 6 grating and cutting discs (I-VI), a kneading blade t and a chopping blade z. The mixing bowl 9 is very versatile to use: grating or cutting, mixing or cutting, kneading or stirring. · Place the lid 0 on the mixing bowl 9. · Insert the ingredients into the mixing bowl 9 through the loading shaft q. · Now switch on the appliance by setting the speed controller 7 to the level recommended in the table. If you are uncertain about the speed, use the fastest level (3). -4- Hints: · Cut the ingredients into approx. · The appliance chops the ingredients very fast, therefore allow the appliance to run only briefly. · Do not allow the appliance to run for more than 1 minute at a time. · Should the ingredients get caught up in the bowl 9 or between the blades z: - Switch off the appliance. - Remove the ingredients with a spatula o. 7. 3 Insert the cutting and grating discs back into the accessory clip · Insert the cutting discs (II/III) in the retainer slots. Begin with the inner retainer slots. The lateral flaps with the elevation in the middle must point upwards. · Place the shredder (IV/V), grater (I) and potato-chips disc (VI) in the storage slot on the outside. 7. 2 Remove the cutting and grating blades from the accessory clip · Remove the blender lid 2 from the blender jug 4 by turning it clockwise. · Grasp the accessory clip 3 on the handle at the centre of the retainer 3 with the thumb and index finger. · Place the accssory clip 3 back in the blender jug 4. Ensure that the rails on the accessory mounting 3 grip firmly into the shoulders of the mixing container 4. · Place the cover 2 on the liquidiser 4 so that the arrows on the handle of the liquidiser 4 and on the cover 2 point towards each other. Turn the cover 2 anti-clockwise until it sits firmly. · Pull the accessory clip 3 with the cutting and grating discs (I-VI) out of the blender jug 4. · Remove the cutting and grating discs (I-VI) from the holder 3. 7. 4 Working with the cutting and grating discs Caution: · The cutting edges are very sharp!· Never use your fingers, spatula, spoon handles or similar objects for pushing foodstuff through the filling shaft q! -5- The cutting (II/III) and grating discs (IV/V) can be used to slice or grate food stuffs quickly. The special potato-chip disc (VI) enables you to make uniform potato-chips at home. With the potato grater disc (I) you can finely chop raw potatoes for the mixture, and finely grate other vegetables or fruits as well. · Place the disc with the leading edge (the side without the ring marking on the corners) in the disc holder i. · Push the other side (marked with two circles at the corners) down until the disc engages with a "click". · Set the speed controller 7 to level 3 (maximum speed) for cutting and grating. Should you wish to process soft fruit or vegetables you can also select a lower speed. [. . . ] Dispose of the appliance through an approved dis-posal centre or at your community waste facility. Dispose of all packaging materials in an environmentally responsible manner. e-mail: support. ie@kompernass. com -9- 13. Importer KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM, GERMANY www. kompernass. com 14. Table for ingredients The following tables should serve you as examples for orientation as regards which ingredients should be processed in what quantities and at what speed level. [. . . ]