User manual SILVERCREST KH 2130

[. . . ] · Only use the product for the intended purpose as described in this operating manual. · Set up the radio transmission set outside of the reach of children. Never allow children to play with the radio transmission set without supervision. Children could attempt to insert foreign objects into the openings in the device housing. [. . . ] · This device is not intended for use by individuals (including children) with restricted physical, physiological or intellectual abilities or deficiences in experience and/or knowledge unless they are supervised by a person responsible for their safety or receive from this person instruction in how the device is to be used. Children must be supervised to ensure that they do not play with the device. Damage to the device · Do not expose the radio transmission set to high temperatures, direct sunlight, severe vibrations or high mechanical loads. · Do not use any aggressive chemical substances for cleaning. -5- The device components Fig. A: The transmitter: q Transmitter w LED status indicator e Switch ROOM 1 r Switch ROOM 2 t Infrared connection socket (IR) y Output for a TV u AV input 2 i AV input 1 o Connection socket a Transmitter's on/off switch s Transmitter channel toggle switch (on the underside of the device) Fig. B: The receiver: d Receiver f Infrared receiver g LED operating indicator h Audio/Video CINCH outputs j Connection socket for the supply voltage k Receiver's on/off switch l Reception channel switch (bottom of device) 1( Wall plug transformer (2 pieces) 2) CINCH--3, 5mm jacks cables (2 pieces) 2!SCART--CINCH adapter "IN" 2@ SCART--CINCH adapter "OUT" 2# Infrared cable with 3 transmit diodes 2$ AUDIO adapter 3. 5 mm mini-stereo to CINCH female 2% CINCH--CINCH cable Putting the device into use First take all device components from the packaging and remove all packing foil and tape. Important notice: Even when the system (transmitter + receiver) is switched off, the manufacturer still recommends disconnecting the wall plug transformer from the mains power or using a power strip with a shut-off switch. Only in this way is complete switch off assured thus contributing to economical consumer attitude. Connecting the transmitter Note: You can connect two signal sources. The signal to be transmitted can be selected via a switch on the front panel of the transmitter. Thereby the radio transmission set can transmit the image and sound signals of every device that emits a sound and/or video signal via a suitable connection: · DVD Player / CD Player · VCR · Television · SAT receiver/set top box · Video camera · Computer video card, etc. Connecting signal sources to the transmitter: · On devices with cinch outputs for the audio and video signals you connect these via one of the supplied CINCH-- 3, 5mm jack cables 2) to the socket "AV IN 1" i on the rear panel of the transmitter q. -6- Note: Observe the colour coding: The white CINCH plug carries the left audio channel signal and belongs in the white CINCH socket. The red CINCH plug carries the right audio channel signal and belongs in the red CINCH socket. The yellow CINCH plug carries the video signal and belongs in the yellow CINCH socket. · If required you can connect a second device as well, with the transmitter and for this select the socket "AV IN 2" u. · If the signal source of your signal is available via a SCART connection, you can use the supplied SCART-- CINCH adapter "OUT" 2@ between the device and the CINCH--3, 5mm jack cable 2). If you, nevertheless, want to connect the signal source to a TV, connect the TV via the socket "OUTPUT TO TV" y to the transmitter q. For this you can use either one of the supplied CINCH--3, 5mm jack cables 2) or, if both are already occupied, an equivalent cable from your local dealer. · For this you connect the supplied infrared cable 2# to the transmitter's infrared connection socket t. · Select on the transmitter and on the receiver, via the CHANNEL switch s and l, implicitly in each case the same transmission channel. This means that compatible devices within the reception range are capable of eavesdropping on the signal. · To switch the signal source AV 1 and/ or 2 for a TV connected to the transmitter q press the button "ROOM 1" e (= the room in which the transmitter is located). · To switch the signal source AV 1 and/ or 2 for a TV connected to the receiver d press the button "ROOM 2" r (= the room in which the receiver is located). · Point the remote control of the signal source to the infrared receiver f of the receiver d. [. . . ] In the event that processing of your complaint is not possible by telephone, here you will receive · a processing number (RMA number) as well as · an address to which you can send your device for repair under warranty. In the case of a mail-in shipment please enclose a copy of the purchase receipt (sales slip). The device must be securely packed and the RMA number clearly visible. Note: The warranty provisions cover only material or manufacturing defects. [. . . ]