User manual SHARP XL570E OPERATION MANUAL

[. . . ] MICRO COMPONENT SYSTEM OPERATION MANUAL MODEL XL-570E XL-560E XL-570E micro component system consisting of XL-570E micro component system and CPXL570H speaker system. XL-560E micro component system consisting of XL-560E micro component system and CPXL560H speaker system. CONTENTS Page SPECIAL NOTES . . Back cover SPECIAL NOTES NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a nonrewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type. [. . . ] q After 2 seconds, the total playing time of the programmed tracks will be displayed automatically. 5 Selected track number Playback order Repeat steps 3 - 4 for any other track Up to 20 tracks can be programmed. ming mode (when MEMORY is flashing) or if you change your mind, the programmed tracks can be cleared by pressing the CLEAR button on the remote control. The tracks will be cleared sequentially starting with the last entered track. q If you make a mistake whilst in the program- 6 Total playing time Caution: q Do not open the CD compartment during playback (or whilst paused). q If the disc is damaged, dirty, or loaded upside down, "NO DISC" or "READ ERR" will appear in the display. q When the unit is not being used, be sure to close the CD compartment. If it is left open, the lens may become covered with dust and the unit may not operate properly. q Playing certain compact discs at a high volume may cause mistracking. q If TV or radio interference occurs during CD operation, move the unit away from the TV or radio. Press the 0 / CD 6 (0 6) button to start playback of programmed selections. To clear all the programmed selections: To cancel a programmed sequence, press the CLEAR button on the remote control whilst the disc is stopped and the "MEMORY" indicator is lit. Notes: q Opening the CD compartment automatically cancels the programmed sequence. q Even if you press the ON/STAND-BY button to enter the stand-by mode or the function is changed from CD to some other function, the programmed selections will not be cleared. q When in the random play mode (whilst "RANDOM" is lit), programming is not possible. To perform some programming, cancel the random play mode. 10 XL-560E/XL-570E(SUK) TINSE0019SJZZ CASSETTE OPERATION s Cassette tape q For playback, use normal or low-noise tape for the best sound. (Metal or CrO2 tape is not recommended. ) For recording, use only normal tape. q Do not use C-120 tapes, tapes with large diameter reels, or poor-quality tapes, as they may cause malfunctions. q Before loading a tape into the cassette compartment, tighten the slack with a pen or pencil. q Cassettes have removable tabs which prevent accidental recording or erasing from taking place. Removing the tab will protect the corresponding side from being erased. Cover the tab holes with adhesive tape to erase or record again. Side A (1) Tab for side B (2) Tab for side A (1) 1 s Tape playback Press the ON/STAND-BY button to turn the power on. Press the FUNCTION button until "TAPE" appears in the display. Open the cassette door by pushing the area marked "7 PUSH EJECT". Press the 2 3 q Press the TAPE button on the remote control. 1 2 5 4 5 0 button. To stop playback: Press the s button. Fast forward/rewind: To advance the tape, press the s button, then press the button. [. . . ] Play a CD on this unit. 1 2 3 Press the ON/STAND-BY button to enter the stand-by mode. Whilst pressing down the MEMORY/SET button and the BASS/TREBLE button, plug the AC power lead into the AC INPUT socket on this unit. Note: q Only CD signals can be output. Caution: q The operation explained above will erase all data stored in memory, such as clock and timer settings, and tuner and CD presets. 17 XL-560E/XL-570E(SUK) TINSE0019SJZZ MAINTENANCE q Amplifier section Output power: Output terminals: Input terminals: RMS; 40 W (20 W + 20 W) (10 % T. H. D. ) Speakers; 4 ohms Headphones; 16-50 ohms (recommended; 32 ohms) Video/Auxiliary (audio signal); 500 mV/47 kohms FM; 87. 5-108 MHz AM; 522-1, 620 kHz Compact disc player Non-contact, 3-beam semiconductor laser pickup 1-bit D/A converter 8-times oversampling digital filter 20 - 20, 000 Hz Unmeasurable (less than 0. 001% W. peak) 50 - 14, 000 Hz (Normal tape) 50 dB 0. 25 % (WRMS) q Tuner section s Internal care q Do not touch the Laser pickup lens. If fingerprints or dust accumulate on the pickup, clean it gently with a dry cotton swab. [. . . ]