User manual SHARP LC-46LD264E

[. . . ] 1 IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV. Model No. : Serial No. : IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrow-head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR TABLE. [. . . ] Press MENU to exit. 3 · Menu options differ in the selected input modes, but the operating procedures are the same. · The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly from the actual screens. Menu Operation Buttons Using the remote control Use the following buttons on the remote control to operate the menu. Using the control panel of the main unit You can also operate the menu with the control panel of the main unit. Button operations on the control panel correspond to the ones on the remote control as shown below. MENU: MENU on the remote control. Press to select a desired item on the screen or adjust a selected item. CH / : Cursor a/b on the remote control. VOLk/l: Cursor c/d on the remote control. 17 On-Screen Display Menu Picture Menu Adjusts the picture to your preference with the following picture settings. Selected item Backlight Contrast Brightness Color Tint Sharpness cbutton The screen dims For less contrast For less brightness For less color intensity Skin tones become reddish For less sharpness dbutton The screen brightens For more contrast For more brightness For more color intensity Skin tones become greenish For more sharpness Color Temp. (Color Temperature) For a better white balance, use color temperature correction. High: Mid-High: Middle: Mid-Low: Low: White with bluish tone White with reddish tone White balance can be adjusted between a maximum of +30 and a minimum of ­30 for each color temperature. R Gain: ­30 through +30 G Gain: ­30 through +30 B Gain: ­30 through +30 · For resetting all adjustment items to the factory preset values, press a/b to select "Reset", and then press ENTER. · For resetting all Picture adjustment items to the factory preset values, press a/b to select "Reset", press ENTER, press c/d to select "Yes", and then press ENTER. OPC Setting Automatically adjusts the brightness of the screen. Off: The brightness is fixed at the value set in "Backlight". On: Display: Displays the OPC effect on the screen while adjusting the brightness of the screen. · When set to "On", the Optical Picture Control (OPC) senses the surrounding light and automatically adjusts the backlight brightness. Make sure nothing obstructs the OPC sensor, which could affect its ability to sense surrounding light. · When set to "On: Display", OPC effect displays on the screen while the OPC adjusts the screen brightness. · Depending on the brightness of the surrounding light, the OPC sensor might not operate if the adjustment range is small. Audio Menu You can adjust the sound quality to your preference with the following settings. Selected item Treble Bass Balance cbutton For weaker treble For weaker bass Decrease audio from the right speaker dbutton For stronger treble For stronger bass Decrease audio from the left speaker No Signal Off When set to"Enable", the power will automatically shut down if there is no signal for 15 minutes. · Five minutes before the power shuts down, the remaining time displays every minute. · When a TV program finishes, this function may not operate. No Operation Off When set to "Enable", the power will automatically shut down if there is no operation for 3 hours. · Five minutes before the power shuts down, the remaining time displays every minute. · "Disable" is the factory preset value. · Audio menu is grayed out when Output Select is set to "Variable". · For resetting all Audio adjustment items to the factory preset values, press a/b to select "Reset", press ENTER, press c/d to select "Yes", and then press ENTER. 19 On-Screen Display Menu Setup Menu EZ Setup You can run EZ Setup again, even after setting up the preset channels. Language: Select from among 3 languages (English, French and Spanish). TV Location: Select "Home" or "Store" for the location where you plan to install the TV. · If you select "Home", AV MODE is set to "STANDARD". · If you select "Store", AV MODE is set to "DYNAMIC (Fixed)". If there is no operation for 30 minutes, AV MODE will return to "DYNAMIC (Fixed)" automatically, regardless of previous changes to the AV MODE settings. Antenna Setup - DIGITAL In order to receive digital air broadcasts, you need a digital broadcast antenna. You can confirm the antenna configuration through the "Antenna Setup DIGITAL" screen. If necessary, adjust the direction of the antenna to obtain the maximum signal strength. Signal Strength: The signal strength of DIGITAL channel is displayed. Channel Strength: Input the 2-digit channel number to check the signal strength of the selected channel. Make sure the signal is strong enough for each channel. · This function is available for DIGITAL (Air) only. Air/Cable: Make sure what kind of connection is made with your TV when selecting "Air" or "Cable". [. . . ] The source code for the software components whose copyrights are held by SHARP is not distributed. Acknowledgements The following open source software components are included in this product: · linux kernel/busybox/uClibc/zlib/libpng/libjpeg CLEARING THE SECRET NUMBER If you forget the secret number, clear the secret number using the following procedure. 1 Select an item from the list below to display the secret number input screen. (For operating the on-screen display menu, see page 17. ) · "EZ Setup", "CH Setup", "Parental CTRL" or "Reset" on the Setup menu. Press and hold both CH and VOLk on the TV simultaneously until the message appears on the screen. 2 The secret number is . · As a precautionary measure, make a note of your secret number above, cut it from this manual, and keep it in a safe place. 30 Calling for Service For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or customer assistance, please call 1-800-BE-SHARP. LIMITED WARRANTY CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. [. . . ]