User manual SHARP AR-335 SECTION 2

[. . . ] CHAPTER 4 SUPPLIES This chapter describes the supplies for this copier such as paper and toner. CHAPTER4 Page q PAPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 4-2 4-5 4-7 q q q STORAGE OF SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 4-1 PAPER Types and sizes of copy paper Size Weight Capacity (80 g/m2 (21lb. ) paper) 500 sheets Special paper Paper trays 1 and 2 Bypass tray A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") 56 to 105 g/m2 (15 lbs. to 34 lbs. )* (Ordinary paper) 50 sheets Transparency film, labels, tracing paper, cover stock** (200 g/m2 (110 lbs. )), index stock** (176 g/m2 (65 lbs. )) q For best results, use only paper recommended by SHARP. [. . . ] Document glass All originals which cannot be copied from the SPF/ RADF must be copied here. Bypass tray paper guides Adjust to the width of the copy paper. 6-2 PART NAMES AND FUNCTIONS Interior Bypass tray Special papers (including transparency film) and copy paper can be fed from the bypass tray. Document feeder indicators (AR-285/AR-335) Original feed indicator Indicates the originals in the tray will be fed. Original reminder Indicates an original is still on the document glass. RADF exit roller cover (AR-285/AR-335) Open to remove misfed originals. RADF feeding roller cover (AR-285/AR-335) Open to remove misfed originals. Photoconductive drum Copy images are formed on the photoconductive drum. Corona unit The unit is used to charge the photoconductive drum. Paper guide Push down to remove misfed paper. GENERAL INFORMATION Part names and functions Accessories Operation manual . 1 Toner collecting containers (including 1 pre-installed at the factory) . 3 6-3 PART NAMES AND FUNCTIONS Operation Panel 1 4 PRINT DATA ON LINE 2 5 8 0 3 6 INTERRUPT CLEAR ALL CA START 7 COPY AUDIT CLEAR 9 PROGRAM CLEAR C P The key and indicators are not used for the copier features. DATA ON LINE 1 4 2 5 8 0 3 CA 6 PRINT 7 COPY ACC. #-C 9 C P LCD touch panel Displays information to assist the operator. Various operation keys are included in the touch panel depending on the particular screen being displayed. CHAPTER6 GENERAL INFORMATION Part names and functions START ( ) key and indicator Copying is possible when the indicator is on. Message display Messages are displayed regarding copier status and operation. Paper size display The sizes of loaded copy paper are displayed and the selected paper feed location is highlighted. 1-7) Press for operation guidance on use of various features of this copier. Press for guidance when a misfeed occurs, when adding toner, or when used toner must be disposed of. CLEAR ALL ( CA ) key Clears all selected settings and returns the copier to the initial settings. CLEAR ( C ) key Press to clear the copy quantity display, or press during a copy run to terminate copying. The copier will stop after copies in progress are finished. 6-4 PART NAMES AND FUNCTIONS Touch Panel (Basic screen) Inch system READY TO COPY. ORIGINAL A4 A4R 1 ORIGINAL 8/2 11 1 8/2 11R 1 1. 8/2 11 2. 11 17 1. A3 AUTO EXPOSURE AUTO A4 PAPER SELECT 100% COPY RATIO 1 AUTO 8/2 11 Depending on the country or area, some keys will be indicated with either an English name or a symbol. CUSTOM SETTINGS ( ) key Press to set key operator programs or adjust the contrast of the touch panel. 2-SIDED COPY key Press to select the 1-sided to 1-sided, 1-sided to 2-sided*, 2-sided to 1-sided (AR-285 and AR-335 only) or 2-sided to 2-sided (AR-285 and AR-335 only) copy mode. * To select the 1-sided to 2-sided copy mode on the AR-280, an optional duplex module (AR-DU1) must be installed. 2-16) Press to select the exposure mode: AUTO, TEXT, TEXT/PHOTO, or PHOTO. [. . . ] PRESS FOR RECOVERY INSTRUCTIONS. 1 OPTIONAL EQUIPMENT Finisher (AR-FN1) While holding the finisher release lever, slide the finisher away from the copier. 2 Remove the misfed paper. CHAPTER7 7-14 FINISHER (AR-FN1) 3 If the misfed paper cannot be removed in step 2, open the cover of the paper feed area of the finisher. 4 Remove the misfed paper. 5 If the misfed paper cannot be removed in step 4, close the cover of the paper feed area and open the top cover. OPTIONAL EQUIPMENT Finisher (AR-FN1) 6 Remove the misfed paper. CHAPTER7 7 Close the top cover. 7-15 FINISHER (AR-FN1) 8 Push the finisher toward the copier and latch it in place. q Confirm that the misfeed display is cleared. A MISFEED HAS OCCURRED. Misfeed in the lower transport area CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. OPTIONAL EQUIPMENT Finisher (AR-FN1) 1 While holding the finisher release lever, slide the finisher away from the copier. CHAPTER7 2 Remove the misfed paper from the paper transport area as shown in the illustration. 7-16 FINISHER (AR-FN1) 3 Open the paper transport area cover of the finisher. 4 Use the transport area lever to open the transport. OPTIONAL EQUIPMENT Finisher (AR-FN1) 5 Remove the misfed paper. CHAPTER7 6 Close the transport. 7-17 FINISHER (AR-FN1) 7 Remove the misfed paper. q Remove the misfed paper from the paper transport area. q If the misfed paper is not seen in the paper transport area, turn the roller rotating knob to feed the paper. OPTIONAL EQUIPMENT Finisher (AR-FN1) Roller rotating knob 8 Close the paper transport area cover. CHAPTER7 9 Push the finisher toward the copier and latch it in place. q Confirm that the misfeed display is cleared. 7-18 FINISHER (AR-FN1) Specifications Tray capacity Top tray: Second tray: Offset tray: 500 sheets 500 sheets 1, 500 sheets (A4 (8-1/2" x 11")) 750 sheets (larger than A4 (8-1/2" x 11")) Paper size Top tray: Second tray: Offset tray: A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") A4 to A3 (8-1/2" x 11" to 11" x 17") 52 to 128 g/m2 (14 lbs. to 34 lbs. ) Paper weight Top tray: Second tray: Offset tray: For paper weighing more than 105 g/m2 (28 lbs. ), A4 (8-1/2" x 11") is the maximum size. Offset Paper size for stapling 30 mm (1. 2 inch) A4, A4R, B4, A3 (8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", 11" x 17") In some regions, 216 mm x 330 mm (8-1/2" x 13") size paper can be used in place of B4 (8-1/2" x 14"). Stapling capacity 50 sheets (80 g/m2 (21 lbs. )) (25 sheets for B4 and A3 (8-1/2" x 14" and 11" x 17") paper) Power supply Weight Dimensions Drawn from the copier Approx. [. . . ]