User manual SHARP AF-06ERL

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP AF-06ERL. We hope that this SHARP AF-06ERL user guide will be useful to you.


SHARP AF-06ERL : Download the complete user guide (655 Ko)

Manual abstract: user guide SHARP AF-06ERL

Detailed instructions for use are in the User's Guide.

[. . . ] ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. [. . . ] Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. If a grounding adapter is used, make sure the receptacle box is fully grounded. 3-Pronged receptacle Grounding adapter Grounded receptacle box 3-Pronged plug Grounding prong Grounded receptacle box Screw Tab for grounding screw Grounding wire 8 PRECAUTIONS NOTES ON OPERATION · Allow 3 minutes for the compressor to restart cooling. If you turn the air conditioner off and immediately restart it, allow three minutes for the compressor to restart cooling. Improperly installed air conditioners and improperly weatherstripped doors and windows will let hot air in and the cool air out. · Turn off air conditioner when no one is home. Use only when necessary. The fewer hours a room air conditioner is used, the lower the operating cost. 9 HOW TO OPERATE PARTS NAMES UNIT !" # $ 1 Front Cabinet % & ' 2 Air Inlet (Indoor Side) 3 Horizontal Louvers 4 Vertical Louvers 5 Air Outlet (Indoor Side) 6 Control Panel 7 Rear Cabinet 8 Air Inlet (Outdoor side) 9 Filter (Pull the filter handle to the right to remove. ) 10 Filter Handle 11 Power Cord CONTROL PANEL F hr POWER ON/OFF ! SLEEP COOL TEMP SELECTOR TIMER ON/OFF ENERGY SAVER " # $ % & ' 1 Receiver window for remote control signal 7 TIMER ON/OFF pad 2 Display 3 SLEEP indicator 4 SELECTOR pad 5 COOL indicator 6 TEMPERATURE setting pad ----Lower 8 TIMER indicator 9 ENERGY SAVER pad 10 ENERGY SAVER indicator 11 POWER ON/OFF pad 12 POWER indicator temp. ----Raise temp. 10 HOW TO OPERATE COOLING OPERATION POWER COOL indicator indicator 1 2 Touch POWER ON/OFF pad. · The unit is preset at 74°F and HIGH COOL. · POWER indicator and COOL indicator will light. F hr POWER ON/OFF SLEEP COOL TEMP SELECTOR TIMER ON/OFF ENERGY SAVER To turn off the unit, touch POWER ON/OFF pad again. · POWER indicator and COOL indicator will go off. POWER ON/OFF pad TO CHANGE FAN SPEED AND OPERATION MODE COOL indicator F hr POWER ON/OFF During operation Touch SELECTOR pad and select the operation mode and fan speed. · Fan speed and operation mode will change as you touch. SLEEP COOL TEMP SELECTOR TIMER ON/OFF ENERGY SAVER HIGH COOL LOW FAN MED COOL MED FAN LOW COOL HIGH FAN SELECTOR pad NOTES ON OPERATION MODE: MODE HIGH COOL MED COOL LOW COOL HIGH FAN MED FAN LOW FAN COOL indicator light on light on light on light off light off light off DISPLAY Cooling operation with high fan speed. Fan only operation with low fan speed. · When the SELECTOR is changed to fan only operation from cooling operation, it will take 5 seconds for the compressor to stop. 11 HOW TO OPERATE TO CHANGE TEMPERATURE SETTING During cooling operation F hr POWER ON/OFF Touch the TEMPERATURE setting pad to adjust the temperature setting. temp. · Temperature can be set within the range of 64°F to 86°F. ---Lower SLEEP COOL TEMP SELECTOR TIMER ON/OFF ENERGY SAVER TEMPERATURE setting pad · Display will change as you touch the pad. NOTE: · In fan only (HIGH FAN, MED FAN, LOW FAN) operation, the temperature display will go off and the temperature setting cannot be changed. · In cases of power outages or when the unit is disconnected; when the power is restored or the unit is plugged in, the unit and display will return to the preset conditions of 74°F and HIGH COOL. The user must touch POWER ON/OFF to resume operation. TO CHANGE AIR FLOW DIRECTION The horizontal louvers are used to adjust the UP/DOWN direction of air flow, and the vertical louvers are used to adjust the LEFT/RIGHT direction of air flow for uniform and efficient cooling of the room. Horizontal louvers Vertical louvers Lever Adjust UP/DOWN air flow Adjust LEFT/RIGHT air flow 12 HOW TO OPERATE ENERGY SAVER OPERATION During normal operation, the thermostat automatically controls cooling and the fan runs continuously. When the ENERGY SAVER OPERATION is selected, the thermostat automatically controls cooling and the fan automatically stops when the compressor is not operating. This will occur within a 20 min time span. ) ENERGY SAVER indicator F hr POWER ON/OFF During cooling operation 1 2 Touch ENERGY SAVER pad. · ENERGY SAVER indicator will light. SLEEP COOL TEMP SELECTOR TIMER ON/OFF ENERGY SAVER To cancel, touch ENERGY SAVER pad again. · ENERGY SAVER indicator will go off. ENERGY SAVER pad NOTE: ENERGY SAVER OPERATION cannot be set during fan only operation. SLEEP OPERATION When SLEEP OPERATION is set, the temperature setting is automatically adjusted to prevent the room from becoming too cold while you sleep. One hour after the SLEEP OPERATION is started, the temperature setting rises 2°F higher than the original temperature setting. The temperature will return to its original setting after 8 hours. SLEEP indicator F hr POWER ON/OFF During cooling operation 1 TEMP TIMER ON/OFF Press the SLEEP button on the remote control. SLEEP SLEEP COOL SELECTOR ENERGY SAVER · SLEEP indicator will light. 2 To cancel, press the SLEEP button again. · SLEEP indicator will go off. NOTE: · SLEEP OPERATION cannot be set during fan only operation. · SLEEP OPERATION will be cancelled in 5 seconds, when cooling operation is changed to fan only operation while SLEEP OPERATION is set. 13 HOW TO OPERATE ON TIMER OPERATION · This unit has a built-in timer that can be programmed to start the unit up to 12 hours in advance. You can set the timer to start in increments of 30 minutes (0. 5 hours) up to 9. 5 hours in advance of the start time, or in 1 hour increments from 10 to 12 hours in advance of the start time. · The unit will start automatically according to your setting. When the unit is not operating COOL indicator 1 F hr POWER ON/OFF Touch the TIMER ON/OFF pad to set the delayed start time. · The time setting will change as you touch the pad. The display will change as follows; Preset(0. 5h) SLEEP COOL TEMP SELECTOR TIMER ON/OFF ENERGY SAVER Previous setting 0. 5h 1. 0h 1. 5h 12h 10h 11h CL(cancel) TIMER ON/OFF pad TIMER indicator (If you wish to start the operation 6 hours and 30 minutes later, set the delay time as shown above. ) · The timer will be set, 5 seconds after the TIMER ON/OFF pad is touched for the last time. · COOL indicator will light when cooling operation is selected. The temperature setting will be displayed. TO CANCEL THE TIMER SETTING Touch the TIMER ON/OFF pad again after the timer is set, or press the TIMER ON/OFF pad until CL(cancel) appears on the display. 14 HOW TO OPERATE OFF TIMER OPERATION · This unit has a built-in timer that can be programmed to shut the unit off up to 12 hours in advance. You can set the timer to stop in increments of 30 minutes (0. 5 hours) up to 9. 5 hours in advance of the stop time, or in 1 hour increments from 10 to 12 hours in advance of the stop time. · The unit will stop automatically according to your setting. When the unit is operating 1 F hr POWER ON/OFF Touch the TIMER ON/OFF pad to set the delayed stop time. · The time setting will change as you touch the pad. [. . . ] Close all windows and doors for maximum cooling. TIMER DOES NOT WORK PROPERLY · If a power failure occurs while the ON or OFF TIMER is set, the TIMER setting will be cancelled and will not resume even after the power is reinstated. This is the normal operation for this unit. NOTE: WATER IN BOTTOM OF TRAY · Water will collect in the bottom tray of the unit. Water condenses on the evaporator coil at the front of the unit and is channeled to the rear where it is picked up by the condenser fan. The water is blown onto the condenser coil fins and this creates a "splashing" noise which is normal. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP AF-06ERL




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP AF-06ERL will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.