User manual SHARP 21QF2-U
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP 21QF2-U. We hope that this SHARP 21QF2-U user guide will be useful to you.
You may also download the following manuals related to this product:
SHARP 21QF2-U (3089 ko)
SHARP 21QF2-U annexe 1 (3089 ko)
Manual abstract: user guide SHARP 21QF2-U
Detailed instructions for use are in the User's Guide.
[. . . ] Example of side terminals usage
E6
TV
To Audio/Video out terminals
DVD Player
VCR
Remote Control
Size-AA batteries
Operation manual
Camcorder
E3
ANTENNA CONNECTION
Connecting to an antenna via a VCR
TV
Video Game
Connecting to an antenna
Yellow : To VIDEO White : To AUDIO
VCR
300-ohm twin-lead flat feeder (not supplied)
75-ohm impedance converter (not supplied)
Example of rear terminals usage
TV For Playback
75-ohm coaxial cable (round cable) (not supplied) Standard DIN45325 plug (IEC 169-2) Antenna in To antenna in terminal To RF out terminal
Yellow : To VIDEO White : To AUDIO
DVD Player
For Recording and Editing VCR
To Audio/Video out terminals
If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC 169-2), plug it into the antenna jack at the rear of the set.
If your outdoor antenna uses a 300-ohm twin-lead flat feeder, connect a 300-ohm to 75-ohm impedance converter and plug it into the antenna jack at the rear of the set.
To Audio/Video out terminals
VCR
To Audio/Video in terminals
· When using the RF terminal connection, set the TV to channel zero to make initial adjustments for the VCR.
· The audiovisual cords required to connect the TV set with video equipment may differ from those shown in the above diagram. See the operation manual of your video equipment for connection details. · The above recording and editing connections are intended solely for personal use and not for the illegal copying of audiovisual material protected by copyright laws.
21QF2-U_EN. indd 2
12/28/07 12:12:06 PM
E5
TV set
PART NAMES
E5
PART NAMES (Continued)
Infrared transmitter window Aim this window at the infrared sensor window on your TV set.
Remote control
TV/VIDEO
Turns the TV on or to Standby mode.
1 2 5 8 0
TV/VIDEO
Switches between TV broadcasts and A/V input programmes. [. . . ] To turn off SKIP, press the number buttons to select the desired channel and then set "SKIP" to "OFF". · MANUAL (FINE tuning) / is pressed, the frequency i) Each time changes to allow fine tuning and the colour of channel number changes to yellow to indicate fine tuning. ii) Press / for more than 2 seconds, the "Manual Channel Tuning" will start. Press Auto tuning bar will shown during Auto Search only.
POSITION COLOUR SOUND SKIP MANUAL AUTO SELECT: CH ADJUST: 27 AUTO B/G OFF 168. 25MHz RETURN:MENU
/
CH
· Press CH and channels change as shown below. / 2 / 1 / 0 . . .
@ With the number buttons (on remote control)
5 · To select a one-digit channel, such as 5, press If "5-" is indicated, press to select one-digit 5 input, and then press again. · To select a two-digit channel, such as 15, press 1 to select the two-digit input. Press , and then 5 press .
.
1 15
PAL B/G
POSITION COLOUR SOUND SKIP MANUAL AUTO SELECT: CH ADJUST:
27 AUTO B/G OFF 168. 25MHz RETURN:MENU
^ Press
MENU
until normal screen appears.
POSITION COLOUR AV1 AUTO
Adjusting volume
!Adjust volume using
/ .
VOLUME 10
· When you select AV1, AV2 for the channel position, the CH-SETTING menu changes as shown on the right and the colour mode changes in the following order:
AUTO PAL SECAM NTSC4. 43 NTSC3. 58
· The volume bar disappears approximately three seconds after the volume has been adjusted.
SELECT: CH
ADJUST:
RETURN:MENU
· When the power indicator lights up dimly, either CH / CH on the TV can be pressed to turn on the power. · Channels that have been skipped cannot be selected by CH / CH . Use TV/VIDEO to select this · The AV1, AV2 input channel cannot be selected using CH channel.
· Switching COLOUR system: Set the system to "AUTO" for normal TV reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the TV set. When the picture is not stable, switching to an appropriate system may improve the picture quality. · Switching SOUND system: When the sound is not stable, switching to an appropriate system may improve the sound quality.
21QF2-U_EN. indd 4
12/28/07 12:12:07 PM
E7
!Press @ Press # Press $ Press
items.
SETTING AND ADJUSTMENT (Continued)
TV/VIDEO
E8
2 5 8 0 3 6 9
FEATURES
TV/VIDEO
Picture adjustment
MENU
Off timer
Automatically turns power off after a set length of time has passed.
CH CH
1 4 2 5 8 0
to call MENU screen. / to select PICTURE icon.
CH
CONTRAST COLOUR BRIGHTNESS TINT SHARPNESS WHITE TEMP SELECT: ENTER: CH 50 0 +10 10 RETURN:MENU
1 4 7
3 6 9
!Press @ Press
CH CH
TIMER
to call "OFF /
".
OFF TV PASSWORD BLUE BACK : OFF 0000 OFF
7
CH CH
MENU
CH
/ /
to enter PICTURE menu. [. . . ] Example: After switching from channel 5 to channel 7, the channel will change to channel 5. is pressed, again to
PAL
TIMER NORMAL
PAL
Sound OK, picture poor.
Picture rolls vertically.
PAL
TV
Picture OK, sound poor.
Picture lines or streaks.
7
Problems
5
LANGUAGE
Remote control does not work.
TV / Video selection
Switches between TV broadcasts and AV input programmes. · Each time you press the TV/VIDEO , the input switches between AV1, AV2 and TV programme.
Possible Causes/Remedies
AV1 AV2 25
PAL B/G
Try a new channel to check for possible station trouble. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP 21QF2-U
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP 21QF2-U will begin.