User manual ROLAND V-SYNTH VERSION 2

[. . . ] Errata We apologize for the following errors in the V-Synth XT Owner's Manual. Please make the corrections listed below. P. 101 left column "The concept of a Rhythm Kit" (Add) P. 39 Step 6 (Incorrect) To save your patch, use the procedure described in "Saving Patches (PATCH Write)" (p. (Correct) To save your patch, use the procedure described in "Saving Patches (PATCH Write)" (p. When you're using Rhythm mode, the effect you specify for the Rhythm part will also apply to the other parts (non-rhythm parts) you're using. P. 102 right column Step 3 (Add) * If you want to save a patch you created in the Sound Shaper, you must also execute "Save Project" (p. 53) in addition to "PATCH Write" (p. 132). [. . . ] When you encode, the newly detected event locations will take effect. The events at the beginning and end of a sample cannot be deleted. Adding an Event 1. By turning the VALUE dial, pressing [INC/+][DEC/-], or dragging your finger over the sample in the screen, move Current to the location at which you want to add the event. Touch to add the event. 119 Creating and Editing Samples (Sample Mode) Creating and Editing Samples (Sample Mode) Saving a Sample Samples that you sample or encode will be lost when you turn off the power. If you want to keep these samples, use the Disk Save Project screen in the Disk mode. Jump to the DISK Save Project screen in the Disk mode. fig. 06-06_50 For details on operations in this screen, refer to "Saving Project on Disk (Save Project)" (p. 132). 120 Settings Common to All Modes (System Mode) Settings that affect the entire operating environment of the V-Synth, such as tuning and MIDI message reception, are referred to as system functions. This section explains how to make settings for the System functions and describes the functions of the different System parameters. When editing a parameter that requires you to specify a value, move the cursor to the value box of that parameter. Then modify the value by either turning the VALUE dial or pressing [INC/+] or [DEC/-]. Repeat steps 3­6 to make the settings for the System function. How to Make the System Function Settings 1. The V-SYNTH MODE MENU window appears. fig. MODE_50 Saving the System Settings (Write) Settings Common to All Modes (System Mode) Changes you make to the System function settings are only temporary--they will be discarded as soon as the power is turned off. If you want to keep any changes you've made in the system settings, you must save them in internal memory. When you perform the save procedure, the data that previously occupied the save destination will be lost. However, the factory setting data can be recovered by performing the Initialization procedure. After you have edited the settings of the System function, touch <Write>, located in the lower right of the screen. 2. The SYSTEM Com Master screen appears. fig. 05-01_50 Initializing the System Settings (Init) The current settings of the system functions can be restored to a set of standard settings, or to the factory settings. Touch <Init>, located in the lower right of the screen. If you want the factory settings to be in effect the next time the V-Synth is powered up, touch <Write> to save the settings. 3. Touch one of the buttons at the bottom of the screen to select the edit group containing the parameters you want to set. Touch one of the tabs in the left of the screen to select the desired editing screen. For details on how the parameters are grouped, refer to "System Parameters" (p. For details on how to use the touch screen, refer to "Basic Touch Screen Operation" (p. 23). 121 Settings Common to All Modes (System Mode) Functions of System Parameters This section explains what the different System parameters do, and also how these parameters are organized. IO fig. 05-01a_50 Settings Common to the Entire System (Common) Master fig. 05-01_50 External Input Type Selects the type of external input used when Oscillator Type (p. MONO R: Input the R signal in monaural. Master Tune Adjusts the overall tuning of the V-Synth. [. . . ] TEL: (2) 666 10529 SYRIA Technical Light & Sound Center Rawda, Abdul Qader Jazairi St. 21, P. O. BOX 13520, Damascus, SYRIA TEL: (011) 223-5384 SWITZERLAND Roland (Switzerland) AG Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383 MARTINIQUE Musique & Son Z. I. Les Mangle 97232 Le Lamantin Martinique F. W. I. TEL: 596 596 426860 Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F. W. I. TEL: 596 596 715222 DENMARK Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200 TURKEY Ant Muzik Aletleri Ithalat Ve Ihracat Ltd Sti Siraselviler Caddesi Siraselviler Pasaji No:74/20 Taksim - Istanbul, TURKEY TEL: (0212) 2449624 UKRAINE TIC-TAC Mira Str. [. . . ]