User manual ROLAND TD3KW

[. . . ] TD-3KW Owner's Manual Thank you, and congratulations on your choice of the Roland Drum System TD-3KW. 201a Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. * For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-3 must be adjusted. 202 Copyright © 2006 ROLAND CORPORATION All rights reserved. [. . . ] Attach the CY-8 so the Roland logo is positioned on the opposite side of the playing area. Tighten the wing nut to obtain the desired movement. Use the included felt washer and the wing nut. fig. CY-Set02. e Wing Nut Felt Washer Specifications CY-8 Size: 12 inches Triggers: 2 (Bow, Edge) Dimensions: 290 (W) x 295 (D) x 47 (H) mm 11-7/16 (W) x 11-5/8 (D) x 1-7/8 (H) inches Weight: 650 g / 1 lb 7 oz Accessories: Wing Nut, Felt Washer, Stopper * Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function. Double sounding may occur if the wing nut is loose. 10 USING THE UNIT SAFELY FD-8 fig. FD-8. e (Hi-Hat Control Pedal) Using the FD-8 Using the FD-8, you can control the opening and closing of the hi-hat sound. Adjusting the Travel of the Pedal Loosen the nut with a tuning key. deep Shift the Arm Open Hi-Hat Strike the hi-hat without pressing the pedal Half Open Hi-Hat shallow Strike the hi-hat with the pedal pressed half-way Closed Hi-Hat Pedal Plate Anchor Bolt Strike the hi-hat with the pedal pressed Foot Closed Completely press down the pedal Control Out Jack Attaching the Anchor Bolts (When Using on the Carpet) Anchor Bolt Spring for the Anchor Bolt The volume of the Foot Closed sound can be adjusted separately (TD-3 Owner's Manual; p. 42). · Connect the FD-8 to the TD-3 before turning on the power. · Do NOT press the pedal when turning on the power. · The tips of the anchor bolts are sharp. · When using on flooring, the anchor bolts may damage the floor. · When the FD-8 is not going to be used for a long period of time, move and fix the arm, allowing longer travel for the pedal. · To avoid damage, do not leave the FD-8 for extended periods of time with the pedal plate depressed. Specifications FD-8 Dimensions: 130 (W) x 396 (D) x 103 (H) mm 5-1/8 (W) x 15-5/8 (D) x 4-1/16 (H) inches Weight: 1. 3 kg 2 lbs 14 oz Accessory: Tuning Key 11 USING THE UNIT SAFELY KD-8 fig. KD-8. e (Kick) Output Jack 3. Use a tuning key supplied with the FD-8 to tighten the screws removed in Step 1 so that the stand is firmly secured. fig. KD-Assy03 Head Stand Anchor Bolt Foot Plate 4. Attach the kick pedal. Position the beater so that it strikes the center of the head, then secure the kick pedal and KD-8 firmly in place. fig. KD-Assy04. e Making the Settings 1. Remove the screws attached to the reverse side of the KD-8's trigger. fig. KD-Assy01 Beater Install the kick pedal securely. Adjusting the Foot Plate Height 2. Pull out the stand in the direction indicated by the arrow until it is fully extended. fig. KD-Assy02 Depending on your kick pedal, it can be unstable when you attach it to the KD-8. Be sure to adjust the foot plate height so that the entire bottom surface of the pedal is attached to the floor. fig. KD-Assy05. e Beater Commercially Available Kick Pedal * Adjust the height so that the entire pedal comes into contact with the floor. 12 1. Loosen the stand's anchor bolts and remove the foot plate. fig. KD-Assy06 Adjusting the Anchor Bolts UNIT SAFELY USING THE When using the kick pedal on a carpet or similar surface, adjust the anchor bolts so their tips protrude from the plate and secure the pedal in place; this will make it easier to use the kick pedal. However, when used on flooring, the anchor bolts may damage the floor. Adjust the anchor bolts correctly. fig. KD-Anchor. e Adjusting the Anchor Bolts When Using on the Carpet When using on the Floor The tips of the anchor bolts are sharp. Set the kick pedal so that the entire bottom surface is attached to the floor. Tighten the anchor bolts securely there to fix the stand and foot plate. fig. KD-Assy07. e When Using a Twin Pedal fig. KD-Pedal1 Position the two beaters equally apart from the center of the pad as shown in the figure at left. If one of the beater is further away from the center than the other, the sound from the further beater will be lower in volume, or will not sound as desired. fig. KD-Pedal2 This hight will vary depending on your kick pedal. Using a twin pedal will result in lower sensitivity as compared to when a single pedal is used. Raise the sensitivity on the sound module. · Install the kick pedal securely. · When moving the setup, be sure to remove the screws and fold the stand. Transporting the KD-8 while it remains open may subject the stand to excessive strain and result in damage to the stand. Specifications KD-8 Dimensions: 272 (W) x 260 (D) x 405 (H) mm 10-3/4 (W) x 10-1/4 (D) x 16 (H) inches Weight: 2. 9 kg 6 lbs 7 oz Accessory: Screws * Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function. 13 . [. . . ] 21, P. O. BOX 13520, Damascus, SYRIA TEL: (011) 223-5384 MARTINIQUE Musique & Son Z. I. Les Mangle 97232 Le Lamantin Martinique F. W. I. TEL: 596 596 426860 Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F. W. I. TEL: 596 596 715222 DENMARK Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200 UKRAINE TIC-TAC Mira Str. Box 180 295400 Munkachevo, UKRAINE TEL: (03131) 414-40 TURKEY ZUHAL DIS TICARET A. S. [. . . ]