User manual ROLAND RD-700 MANUAL 2

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the Roland Digital Piano RD-700. Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's Manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. . Copyright © 2001 ROLAND CORPORATION All rights reserved. [. . . ] The Edit Menu screen appears. fig. Editmenu2. eps_150 NOTE While the Bulk Dump is in progress, no sounds are produced even when the keys are pressed. In addition, Rhythms and arpeggios being played are also stopped. Bulk Dump Temporary 6. Press CURSOR [ fig. Editmenu2. eps_150 ]. A screen like the one shown below appears. 7. The message "Now, Executing. . . " appears in the display during transmission of the data. After the transmitting is finished, the display will indicate "COMPLETED. " 3. Press CURSOR [ fig. utility1. eps_150 ] to select "9. Utility. " ] to display the Edit screen. You are returned to the Edit screen. Stop the external sequencer. Edit Mode 92 Detailed Settings for Each Function ([EDIT]) Bulk Dump SETUP 6 Press CURSOR [ ]. A screen like the one shown below appears. Restoring saved settings to the RD-700 When returning settings saved to an external sequencer back to the RD-700, an Exclusive message is transmitted from the external sequencer, then the data is received by the RD-700. NOTE Be aware that when you restore SETUPs data to the RD-700, the data in the RD-700 will be overwritten and lost. Use a MIDI cable to connect the MIDI OUT connector of the external sequencer to the MIDI IN connector of the RD-700. Set the device ID number to the same setting as when you performed the bulk dump. Parameter From Value Setup number for the first Setup to be transmitted. Determines whether the system settings are to be transmitted (YES), or not (NO). To Setting the Device ID Number "Setting the Device ID Number (Device ID)" (p. If the [EDIT] indicator is lit, press [EDIT] to turn the indicator light off and put the RD-700 in normal performance mode. After the transmitting is finished, the display will indicate "COMPLETED. " Send System 7. Press CURSOR [ ]/[ ] and [INC/YES]/[DEC/ NO] to set the transmitted SETUPs. Press CURSOR [ fig. Editmenu2. eps_150 ]. A screen like the one shown below appears. NOTE After playback of the Bulk Dump SETUP data, the RD-700 writes the data to the internal memory. Be sure never to turn off the power while this data is being written (while "Now, writing Bulk Dump Data. A screen like the one shown below appears. fig. Editmenu2. eps_150 For details on transmitting exclusive data, refer to the owner's manual for your sequencer. NOTE Play back the external sequencer at the same tempo you used when performing the bulk dump. If you use a faster tempo, the data may not be restored correctly. Edit Mode 11. After the transmitting is finished, the display will indicate "COMPLETED. " You are returned to the Edit screen. Stop the external sequencer. NOTE Data cannot be received if the Device ID of the receiving device differs from the Device ID used when Bulk Dump was carried out. NOTE Exclusive messages cannot be received when set to GM Mode (p. Carry out the operation after first exiting GM Mode. 93 Detailed Settings for Each Function ([EDIT]) Restoring the settings to the factory condition (Factory Reset) The settings stored in the RD-700 can be returned to their factory settings. 6. The confirmation message appears. fig. LCD NOTE Executing "Factory Reset All" results in deletion of the Setups (p. [. . . ] 21, P. O. BOX 13520, Damascus, SYRIA TEL: (011) 223-5384 Roland Shanghai Electronics Co. , Ltd. (GUANGZHOU OFFICE) 2/F. , No. 30 Si You Nan Er Jie Yi Xiang, Wu Yang Xin Cheng, Guangzhou 510600, CHINA Tel: (020) 8736-0428 NEW ZEALAND Roland Corporation Ltd. 32 Shaddock Street, Mount Eden, Auckland, NEW ZEALAND TEL: (09) 3098 715 CZECH REP. K-AUDIO Kardasovska 626. TEL: (2) 666 10529 SWEDEN Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. S-131 30 Nacka SWEDEN TEL: (0)8 702 00 20 HONG KONG Tom Lee Music Co. , Ltd. [. . . ]