User manual ROLAND PR-1

[. . . ] No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING - When using electric products, basic precautions should always be followed, including the following: 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] For more details about these procedures, refer to "Capturing Video from a Video Deck or Other Device" (p. 78). Editing Palettes and Clips You can change palette and clip names, change their sequence, and perform various other editing functions. For more on palette and clip editing procedures, refer to "Editing Palettes" (p. 66). 60 Introduction to Use of the PR-1 -- Saving Projects Saving Projects Click the [Save] button in the upper part of the screen. The project is updated and saved. fig. editmode05. eps [Save] button You cannot change a project's name and then save the project under the different name. For more on backing up projects, refer to "Copying Projects" (p. 85). Introduction When You Want to Remake the Project Settings If you want to revert the settings for a project (restoring the settings as they were when last saved), click the [Open] button to open the project again. At this point a message asking whether or not you want to save the project appears. Select "Discard. " 61 Introduction to Use of the PR-1 -- Using V-LINK Using V-LINK V-LINK ( ) is a function that makes it easy to exhibit video material during musical performances. Connecting a V-LINK compatible MIDI device to the PR-1 and pressing the VLINK button on the MIDI device provides you with easy control of Presenter. fig. connection. Vlink02. eps Connection example Remote control (V-LINK) MIDI keyboard PR-1 Projector Mouse Connect the USB interface to the [USB] connector on the PR-1 using a USB cable. The USB MIDI interfaces that can be used for this function are shown below. To edit a palette, right-click on the palette and work from the context menu that is displayed. Practical Use fig. edit. palette01. fig. edit. palette01. eps Context menu Palettes list 63 Practical Use of the PR-1 -- Making the Settings for the Project Changing Palette Names 1. Right-click on the name of the palette whose name you want to change in the "Palettes" list. A context menu appears. 2. Select [Rename] to highlight the palette name. Enter the new name using the keyboard. 3. When you have finished typing the name, press the [Enter] key to confirm it. Rearranging Palette Sequences Drag and drop the palettes you want to reorder right inside the "Palettes" list. Right-click on a palette whose position you want to change in the "Palettes" list. A context menu appears. 2. Select [Swap with previous] or [Swap with next]. The palette switches positions with the one before or after it. Deleting Content from the Palette 1. Right-click on the name of the palette whose content you want to delete in the "Palettes" list. A context menu appears. 2. Select [Clear palette]. The palette's content is deleted. 64 Practical Use of the PR-1 -- Making the Settings for the Project Making the Palette Settings You can make the Loop mode settings for all of the clips in a palette simultaneously. You can have the same clip play repeatedly, play the subsequent clip after the current clip is finished, or specify another clip to play back. [. . . ] 66 Selecting Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Selecting Palettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 37 Setting Automatic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]