User manual ROLAND MG-10

[. . . ] No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Roland is a registered trademark of Roland Corporation in the United States and/or other countries. USING THE UNIT SAFETY About WARNING and CAUTION Notices About the Symbols The symbol alerts the user to important instructions or warnings. The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). [. . . ] · Connect the MG-10 to the computer before starting the software. · Do not disconnect the MG-10 from the computer while the software is running. · Select the MG-10 for the software's audio device setting. · The MG-10 will not operate in the Mac OS X Classic environment. Use the DUOCAPTURE when the Classic environment is not running. Playing Back Audio Set to match the software's sample rate setting MG-10 bottom panel MG-10 rear panel Software's Audio Output Device: MG-10 Front panel 15 Basic Use Recording Audio Set to match the software's sample rate setting MG-10 bottom panel Software's Audio Input Device: MG-10 Cassette deck Turntable or * We recommend using one input jack (i . e . , either the LINE jack or the MIC/GUITAR jack) at a time . If devices are connected to both jacks at the same time, the sound input via both jacks is mixed together, but the MG-10 cannot adjust the balance of the mix . Set the [Hi-Z] button and the [INPUT GAIN] button as described below depending on the audio device that is connected. Device Microphone Guitar Cassette deck Turntable [Hi-Z] button OFF ON -- (Either ON or OFF is acceptable) [INPUT GAIN] button HI LO LO Note When recording a musical instrument such as a guitar, we recommend turning on the input monitor (p. You can listen to the instrument's output directly without passing the audio signal through the computer. When the input monitor is turned off, the instrument's audio signal passes through the computer, therefore the sound may be delayed. If sound is doubled when the [INPUT MONITOR] button is set to "ON, " set the [INPUT MONITOR] button to "OFF (AUTO). " * Howling could be produced depending on the location of microphones relative to speakers . 16 Troubleshooting If you experience problems, read this chapter first. Cannot change driver settings (Windows 7) Is the monitoring function of Windows turned on? 18 Troubleshooting Problem Confirmation Is the driver installed?Exit all programs that are using the MG-10, disconnect the MG-10's USB cable, and then reconnect it. Exit all programs that are using the MG-10, disconnect the MG-10's USB cable, and then reconnect it. Exit all programs that are using the MG-10, disconnect the MG-10's USB cable, and then reconnect it. Make sure that the software's audio sample rate setting matches the MG-10's sample rate setting. After changing the MG-10's sample rate, exit all programs that are using the MG-10, disconnect the MG-10's USB cable, and then reconnect it. 26). Is the MG-10's USB indicator off? Is another program using the DUOCAPTURE? Cannot play back or record Did the computer enter standby (suspend) mode, hibernate mode, or sleep mode while the MG-10 was connected?Did you disconnect and reconnect the USB cable while using the DUOCAPTURE? Is the computer's volume setting turned down?(Windows 7) 19 Troubleshooting Problem Confirmation Was the MG-10 connected to the computer while the computer was starting up?Cannot play back or record Did the computer perform a processorintensive task while you were using the MG-10?No sound from computer's speakers Resolution Connect the MG-10 after the computer has started up. [. . . ] When "Are you sure you want to uninstall the driver?" appears, click [OK] . The authentication dialog box or the message "Uninstaller requires that you type your password" will appear . When "Uninstallation is completed . " appears, click [Restart] and restart the computer . It may take some time for the computer to restart. Advanced Driver Settings You can set the input and output audio buffer size and ASIO-related settings. Windows When using Windows 7, driver settings cannot be changed while the monitoring function of Windows is enabled. Turn off the monitoring function ("Monitoring Function Settings (Windows 7)" (p. [. . . ]