User manual ROLAND HP-600

[. . . ] mm, ll: ignored Controller Pitch Bend Change Modulation Expression Hold 1 Portamento Sostenuto Soft RPN Local Control (Controller number 122) Status BnH 2nd byte 7AH 3rd bytes vvH 0H-FH (ch. 1-ch. 16) 00H, 7FH (0, 127) 00H: Local Off 7FH: Local On MSB LSB mmH --- n = MIDI channel number: vv = Control value: 00H 01H mmH llH All Notes Off (Controller number 123) Status BnH 2nd byte 7BH 3rd bytes 00H 0H-FH (ch. 1-ch. 16) 00H 02H mmH --- n = MIDI channel number: * 00H 05H mmH llH When All Notes Off is received, all notes on the corresponding channel will be turned off. However if Hold 1 or Sostenuto is ON, the sound will be continued until these are turned off. 7FH 7FH --- --- OMNI OFF (Controller number 124) Status BnH 2nd byte 7CH 3rd bytes 00H 0H-FH (ch. 1-ch. 16) n = MIDI channel number: * The same processing will be carried out as when All Notes Off is received. *1 Program Change Status CnH 2nd bytes ppH 0H-FH (ch. 1-ch. 16) 00H-64H (prog. 1-prog. 101) OMNI ON (Controller number 125) Status BnH 2nd byte 7DH 3rd bytes 00H 0H-FH (ch. 1-ch. 16) n = MIDI channel number: pp = Program number: * n = MIDI channel number: * The same processing will be carried out as when All Notes Off is received. *1 After a Program Change message is received, the sound will change beginning with the next Note-on. [. . . ] Regarding the checksum please refer to "Supplementary material" (p. 5). System Exclusive Message Status F0H Data byte iiH, ddH, . . . . . . , eeH Status F7H F0H: ii = ID number: dd, . . . , ee = data: F7H: System Exclusive Message status an ID number (manufacturer ID) to indicate the manufacturer whose Exclusive message this is. ID numbers 7EH and 7FH are extensions of the MIDI standard; Universal Non-realtime Messages (7EH) and Universal Realtime Messages (7FH). 00H-7FH (0-127) EOX (End Of Exclusive) The System Exclusive Messages received by this instrument are; Universal Non-realtime System Exclusive messages and Data Set (DT1). Universal Non-realtime System Exclusive Messages Identity Request Message Status F0H Byte F0H 7FH 10H 06H 01H F7H * Data byte 7FH, 10H, 06H, 01H Explanation Exclusive status ID number (universal realtime message) Device ID Sub ID#1 (General Information) Sub ID#2 (Identity Request) EOX (End Of Exclusive) Status F7H Device ID = 10H or 7FH Data transmission This instrument can receive parameters using System Exclusive messages. The exclusive message of HP107 data has a model ID of 00 7EH and a device ID of 10H (17). Data set 1DT1 This is the message that actually performs data transmission, and is used when you wish to transmit the data. Status F0H Byte F0H 41H 10H 00H 7EH 12H aaH Data byte 41H, 10H, 00H, 7EH, 12H, aaH, bbH, ccH, ddH, . . . eeH, sum Status F7H Explanation Exclusive status ID number (Roland) Device ID Model ID Model ID (HP107) Command ID (DT1) Address MSB: upper byte of the starting address of the transmitted data 3 Version 1. 00 Date:June10, 2004 2. Transmit data Channel Voice Messages Note off Status 8nH 2nd byte kkH 3rd byte vvH 0H-FH (ch. 1-ch. 16) 00H-7FH (0-127) 00H-7FH (0-127) Program Change Status CnH 2nd bytes ppH 0H-FH (ch. 1-ch. 16) 00H-64H (prog. 1-prog. 101) n = MIDI channel number: pp = Program number: n = MIDI channel number: kk = note number: vv = note off velocity: System Realtime Message Active sensing Status FEH Note on Status 9nH 2nd bytes kkH 3rd byte vvH 0H-FH (ch. 1-ch. 16) 00H-7FH (0-127) 01H-7FH (1-127) * This will be transmitted constantly at intervals of approximately 250 ms. n = MIDI channel number: kk = note number: vv = note on velocity: System exclusive messages Universal Non-realtime System Exclusive Messages Identity Reply Status F0H F0H Byte F0H 7EH 10H 06H 02H 41H 7EH 01H 00H 00H 00H 01H 00H 00H F7H * Data byte 7EH, 10H, 06H, 02H, 41H, 7EH, 01H, 00H, 00H, 00H, 01H, 00H, 00H Explanation Exclusive status ID number (universal non-realtime message) Device ID (use the same as the device ID of Roland) Sub ID#1 (General Information) Sub ID#2 (Identity Reply) ID number (Roland) Device family code (LSB) Device family code (MSB) Device family number code (LSB) Device family number code (MSB) Software revision level Software revision level Software revision level Software revision level EOX (End of Exclusive) Status F7H Control Change Bank Select (Controller number 0, 32) Status BnH BnH 2nd bytes 00H 20H 3rd byte mmH llH 0H-FH (ch. 1-ch. 16) 00H, 00H-7FH, 7FH (bank. 1-bank. 16384) n = MIDI channel number: mm, ll = Bank number: Volume (Controller number 7) Status BnH 2nd bytes 07H 3rd byte vvH 0H-FH (ch. 1-ch. 16) 00H-7FH (0-127) n = MIDI channel number: vv = Volume: Expression (Controller number 11) Status BnH 2nd bytes 0BH 3rd byte vvH 0H-FH (ch. 1-ch. 16) 00H-7FH (0-127) n = MIDI channel number: vv = Expression: When Identity Request is received, Identity Reply message will be transmitted. Hold 1 (Controller number 64) Status BnH 2nd bytes 40H 3rd byte vvH 0H-FH (ch. 1-ch. 16) 00H-7FH (0-127) Data transmission This instrument can receive parameters using System Exclusive messages. The exclusive message of HP107 data has a model ID of 00 7EH and a device ID of 10H (17). n = MIDI channel number: vv = Control value: Data set 1DT1 This is the message that actually performs data transmission, and is used when you wish to transmit the data. Status F0H Byte F0H 41H 10H 00H 7EH 12H aaH bbH ccH ddH : : eeH sum F7H * * Data byte 41H, 10H, 00H, 7EH, 12H, aaH, bbH, ccH, ddH, . . . For data where greater precision is required, we must use two or more bytes. We will assume that in the exclusive message we are transmitting, the address is aa bb ccH and the data or size is dd ee ffH. remainder 128 - remainder = checksum In other words, the above messages specify a value of 0C 00H for RPN parameter number 00 00H on MIDI channel 4, and then set the RPN parameter number to 7F 7FH. RPN parameter number 00 00H is Pitch Bend Sensitivity, and the MSB of the value indicates semitone units, so a value of 0CH = 12 sets the maximum pitch bend range to +/- 12 semitones (1 octave). (On HP107 the LSB of Pitch Bend Sensitivity is ignored, but the LSB should be transmitted anyway (with a value of 0) so that operation will be correct on any device. ) Once the parameter number has been specified for RPN, all Data Entry messages transmitted on that same channel will be valid, so after the desired value has been transmitted, it is a good idea to set the parameter number to 7F 7FH to prevent accidents. It is not desirable for performance data (such as Standard MIDI File data) to contain many events with running status as given in <Example 4>. This is because if playback is halted during the song and then rewound or fast-forwarded, the sequencer may not be able to transmit the correct status, and the sound source will then misinterpret the data. It is also necessary that the RPN parameter number setting and the value setting be done in the proper order. On some sequencers, events occurring in the same (or consecutive) clock may be transmitted in an order different than the order in which they were received. For this reason it is a good idea to slightly skew the time of each event (about 1 tick for TPQN = 96, and about 5 ticks for TPQN = 480). * TPQN: Ticks Per Quarter Note The Scale Tune Feature (address: 40 1x 40) The scale Tune feature allows you to finely adjust the individual pitch of the notes from C through B. Though the settings are made while working with one octave, the fine adjustments will affect all octaves. [. . . ] For example, the settings introduced below will set the unit to use the Arabian Scale. Example Settings Note name Equal Temperament C C# D D# E F F# G G# A A# B 0 0 0 0 0 0 0 0 0 0 0 0 About tuning To tune the HP107 via MIDI, transmit RPN #1 (Master Fine Tuning) over any MIDI channel. (The tuning is adjusted for all of the parts, regardless of the MIDI channel over which the message is received. ) HP107 is tuned by sending RPN #1 (Master Fine Tuning) to one of MIDI channels 1-16. Tuning of all parts are set even if the message is received at one MIDI channel. [. . . ]