User manual ROLAND CUBE-80X

[. . . ] Owner's Manual Bedienungsanleitung Guide d'utilisation Manuale dell'utente Manual del usuario Manual do proprietário Gebruikershandleiding I 202 Copyright © 2009 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Nederlands Português Español Italiano Français Deutsch English 2 201b Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS", "USING THE UNIT SAFELY" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's Manual should be read in its entirety. [. . . ] By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. 3. 943 Make sure that all volume controls on this unit and connected devices are set to 0. Turn on all the devices connected to this unit's INPUT jack and AUX IN jack. Turn on this unit. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. 942 * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. 4. Before switching off the power, lower the volume on each of the devices in your system, and then turn off the devices in the reverse of the order followed when switching them on. If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. 4). 945 * 10 Panel Descriptions Rear Panel Recorder, etc. Speaker Cable INPUT External Speaker Deutsch 1 2 3 4 6 7 8 5 PCS-31 BOSS FS-6, etc. DELAY/LOOPER MUTE TAP/REC/PLAY/DUB REVERB EFX SOLO CH SELECT Headphones Foot Switches 921 Mixer, etc. connections. FOOT SW Jacks FOOT SW TYPE Switch Either momentary or latch type footswitch pedals can be used with this unit. However, be sure to connect only a momentary-type footswitch such as the BOSS FS-5U to the TAP/REC/PLAY/DUB jack. A latch-type footswitch pedal may fail to operate correctly. * * The footswitch pedal is available separately. The BOSS FS-6 can operate as either a momentary or latch-type pedal switch. * This unit is equipped with a TRS-type FOOT SW jack that accepts plugs of the configuration shown in the figure. To connect a footswitch pedal, use a TRS-compatible cable such as the optionally available PCS-31. TIP RING 11 Nederlands Momentary type: This type remains on (or off) while depressed and switches off (or on) when released. BOSS FS-5L, etc. Português Español * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any Italiano Français English Panel Descriptions Connection and Settings When Using an FS-5L or Latch-type Footswitch Pedal When you're using the FS-6 or FS-5L, you can determine whether the footswitch pedal is on or off by checking its indicator light. Jack TIP: TAP/REC/PLAY/DUB For DELAY: Adjusts the delay time For LOOPER: LOOPER operation (p. 17) Function RING: DELAY/LOOPER MUTE For DELAY: Switches DELAY on and off For LOOPER: Mutes LOOPER When connecting the FS-5L CUBE-80X Rear Panel Red (RING) Jack TIP: EFX Switches EFX on and off RING: REVERB Switches REVERB on and off Jack TIP: SELECT Switches between the JC CLEAN and LEAD channels RING: SOLO Calls up the SOLO function PCS-31 White (TIP) PCS-31 Polarity switch Red (RING) White (TIP) Polarity switch TAP/REC/PLAY/DUB DELAY/LOOPER MUTE REVERB SOLO EFX SELECT PCS-31 Red (RING) White (TIP) Red (RING) PCS-31 White (TIP) When connecting the FS-6 CUBE-80X Rear Panel DELAY/LOOPER MUTE TAP/REC/PLAY/DUB REVERB SOLO EFX SELECT Set the switches as shown as bellow. B A 12 Panel Descriptions Important Notes When Using a Latch-type Footswitch Pedal Normally, the on/off state of the footswitch pedal takes precedence over the control panel for switching EFX, delay, or reverb on and off. However, the on or off states stored in memory using the SOLO function take precedence when saved SOLO-function panel settings are called up. Such cases may result in conflicting indicator displays on the control panel and the footswitch pedal, but this is not a malfunction. To make the indicator displays match up Depress the footswitch pedal whose indicator display is different. Deutsch To make the on/off state of the footswitch pedal take priority at all times On this unit, you can use either of the following settings to control operation when the panel settings for EFX, delay, and reverb are called up using the SOLO function. · Make the on/off state of the footswitch pedal always take priority · Make the on/off state saved using the SOLO function take priority (default) Hold down the TAP and SELECT switches at the same time and switch on the power. [. . . ] 8th Floor, Railway Plaza, 39 Chatham Road South, T. S. T, Kowloon, HONG KONG TEL: 2333 1863 CENTRAL/LATIN AMERICA ARGENTINA Instrumentos Musicales S. A. Av. Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700 DENMARK Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200 SWITZERLAND Roland (Switzerland) AG Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383 TURKEY ZUHAL DIS TICARET A. S. No. 37 Beyoglu - Istanbul / TURKEY TEL: (0212) 249 85 10 MEXICO Casa Veerkamp, s. a. MEXICO TEL: (55) 5668-6699 FINLAND Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)9 68 24 020 UKRAINE EURHYTHMICS Ltd. [. . . ]