User manual ROLAND AR-3000

[. . . ] ) trademarks. * Roland Corporation is an authorized licensee of the CompactFlashTM and CF logo ( * MMP (Moore Microprocessor Portfolio) refers to a patent portfolio concerned with microprocessor architecture, which was developed by Technology Properties Limited (TPL). Roland has licensed this technology from the TPL Group. Copyright © 2006 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Use the SELECT dial to choose "4. 7 Card Convert, " then press the dial. Turn the SELECT dial to choose the Convert, then press the dial. fig. 12-g05e · AR-3000 AR-2000: This converts a card in AR-3000 format to AR-2000 format. · AR-2000 AR-3000: This converts a card in AR-2000 79 Making Settings and Edits for Individual Cards Card Conversion Chart/Conversion Error Chart fig. 12-01e Card Conversion (AR-3000AR-2000)Chart * This chart shows compatibility for converted cards used on the AR-2000. When you're using on the AR-100 or AR-1, refer to the owner's manual for the respective device. 1 Phrase Information Effective without change Converted to similar values Not valid Result in an error and halt conversion 1. 1 Playback Volume (10%--100%) 1. 2 Delay Time (00s00f­59s29f) Conversion of frames to seconds 1. 3 Playback Point Error when playback point is set 1. 4 Repeat Play OFF ON Repeat (1­99) Repeat Interval (00m00s­59m59s) 1. 5 Loop Play Disabled 1. 6 Fade Disabled 1. 7 Control Out OFF ON Offset Time (00m00s­59m59s) 1. 8 MIDI Playback Tempo (5­260) 1. 9 Phrase Name Up to 11 characters State of recording settings REC-In (Selecting the Recording Connector) LINE-IN MIDI Rec: OFF MIDI Rec: OFF LINE+MIC-IN MIDI Rec: OFF DIGITAL-IN MIDI Rec: ON MIDI-IN RDAC-Grade ANNOUNCE LONG2 LONG1 STANDARD HIGH HIGH S-HIGH RDAC-Mode MODE1 MODE2 MODE3 LINEAR H-LINEAR 2 Phrase Combination 2. 1 Pattern Phrase Pattern Phrase Modes SEQUENTIAL RANDOM1 RANDOM2 RANDOM3 Interrupt phrase interval (1­25) Playback sequence (No. 001­128) Assigned phrase (A0001­B1000) Volume (10%­100%) Interval (00. 0s­59. 9s) Error when pattern phrase is assigned to pattern phrase RANDOM RANDOM RANDOM Disabled Valid for No. 001 through 500 Error when 501 or more are present Disabled Error when song phrase is present MODE2 MODE2 MODE2 REC Type STEREO MONO Trig Level (Trigger Recording Settings) OFF LOW MID HIGH MIDI Time Base 192 240 2. 2 Song phrase 4 Settings for Card Editing 4. 1 Card Format Select Max Phrases 250 500 1000 Recording Phrase Protection 4. 5 Card Protect OFF ON Recording settings for recorded phrased RDAC-Grade ANNOUNCE LONG2 LONG1 STANDARD HIGH S-HIGH 4. 6 Card Name 5 Settings for Control Input 5. 1 Control Input Mode DIRECT PLAY PROGRAM PLAY BINARY PLAY BINARY REC BINARY1 Normal Valid for No. 001 through 500 Error when 501 or more are present Trigger Mode: Level Trigger Mode: Level Trigger Mode: Edge Trigger Mode: Level Disabled Disabled 5. 2 Direct Play Normal First-In Last-In Sequence Phrase assignment (1­16) Assigned phrase (PLAY, -----, A0001­B1000) RDAC-Mode MODE1 MODE2 MODE3 LINEAR H-LINEAR REC Type STEREO MONO 5. 3 Program Play Program (1­5) Played back in order Assigned phrase (A0001­B1000) MIDI Time Base 192 240 5. 4 Binary Play <Level: Edge> OFF: OFF ON: OFF OFF: ON ON: ON 5. 5 Binary Recording Phrase select BINARY1 BINARY2 80 Making Settings and Edits for Individual Cards fig. 12-02e Conversion Error Chart In situations like the ones described below, an error occurs and conversion stops. Take action as described in the remedy, then carry out card conversion again. 6 MIDI settings 6. 1 MIDI Output (MIDI OUT/THRU) OUT THRU 6. 2 MIDI Note Map Assigned phrase (A0001­B1000) When there is insufficient space on the destination card for conversion If you are carrying out conversion using two cards, the copy-source card and the copy-destination card do not need to be of the same capacity, but card conversion is not possible unless the usable space on the destination card is larger than the used space on the source card. 6. 3 MIDI Note Out 6. 4 MIDI Channel 6. 5 Note Trigger Trigger Gate Valid for No. 001 through 500 Error when 501 or more are present Disabled (Always output when MIDI Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled output is set to OUT) Action 1: Use a card for the copy destination that has a greater amount of available space than that used on the card-source card. Action 2: Reduce the space used on the copy-source card, such as by deleting unneeded phrases. When you convert a card in AR-2000 format to AR-3000 format, the amount of space used after conversion may increase somewhat. * You cannot change the phrase number after recording, so be sure to select the phrase number you want to record. Hold down the STOP button and press the PLAY button to go into recording standby. fig. 13-g01e Controlling the unit by using MIDI signals is described in another chapter. Refer to "Controlling the AR-3000 Using MIDI Signals (MIDI Control)" (p. 105). Connecting Equipment fig. 13-01e (MIDI Connections) During recording standby, the PLAY indicator and the PAUSE indicator flash in red. MIDI IN MIDI OUT MIDI OUT · If you try to re-record a phrase that's already been recorded, a prompt message appears. If you choose "YES" and press the ENTER button, the recorded data for the phrase is deleted and the unit goes into recording standby. If you choose "NO, " the unit returns to the normal display. MIDI Sequencer * Please be aware that data deleted here cannot be recovered, even if you cancel recording standby without recording anything. 77)" is set to "ON, " recorded phrases are protected and recording is not possible (writing, overwriting, deleting, and editing card data is prohibited). Powered Speaker (for monitor) MIDI IN MIDI Sound Module 82 Recording and Playing MIDI Data Selecting the Recording Connector When you're recording MIDI data, choose "MIDI-IN" as the recording connector. Starting and Ending Recording 1. Pressing the PLAY or PAUSE button while in recording standby starts recording. Press the STOP button to end recording. Procedure for Selecting the Recording Connector 1. Turn the SELECT dial to choose the MIDI-IN, then press the ENTER button. ig. 13-g02e * Please be aware that if you press the SELECT dial instead of the ENTER button, the setting is not confirmed. [. . . ] 71 Trigger Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 F Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Frame Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]