User manual ROLAND AR-1000

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 002a · Do not open or perform any internal modifications on the unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . · Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). [. . . ] Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off. When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated. 2 352b · · When handling the board, grasp it only by its edges. Avoid touching any of the electronic components or connectors. 3 · When handling the board, grasp it only by the panel or the board's edges. Avoid touching any of the electronic components or connectors. 4 355b · · Before you connect any cables, make sure they do not carry a static electricity charge. Such charges can be transmitted, for example, if the other end of the cable has been in contact with a carpet (or other object) where there is a static electricity buildup. 5 · Save the bag in which the board was originally shipped, and put the board back into it whenever you need to store or transport it. 901(F) Maintenance 401a · · For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, nonabrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation. Veuillez suivre attentivement les instructions suivantes quand vous manipulez la carte afin d'éviter tout risque d'endommagement des pièces internes par l'électricité statique. · Toujours toucher un objet métallique relié à la terre (comme un tuyau par exemple) avant de manipuler la carte pour vous décharger de l'électricité statique que vous auriez pu accumuler. 1 402 · 2 · Lorsque vous manipulez la carte, la tenir par les côtés. Retirer du panneau arrière les deux vis de la fente pour la carte d'option et retirer le couvercle. Retirer du panneau supérieur les quatre vis pour la carte d'option et retirer le couvercle. 3 7. Insérer à fond le connecteur de la carte d'option dans le connecteur de l'unité. 3. Use the [SELECT] dial to select "10. 2 Network Address, " then press the dial. Turn the [SELECT] dial to select the setting value, then press the dial. The entry location shown below is highlighted. Turn the [SELECT] dial to select the characters for the password (letters or numbers), then press the dial. fig. 9. 4. Repeat the operation in step 3. Once you've finished supplying values for the settings, press the [ENTER] button. A screen asking you to confirm the write procedure appears. (The confirmation screen appears even if you enter the final item and press the dial. ) To write the settings to the unit, press the [ENTER] button. To cancel, use the [SELECT] dial to choose "NO, " then press the [ENTER] button. You are returned to the Setting Item Selection screen. * The settings for the network address will take effect the next time you power up. Repeat step 7. When you have finished entering the password (5 to 8 characters), press the [ENTER] button. (The confirmation screen appears even if you enter the final item and press the dial. ) To cancel, use the [SELECT] dial to choose "NO, " then press the [ENTER] button. [. . . ] Rua San Jose, 211 Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666 DENMARK Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200 RUSSIA MuTek Dorozhnaya ul. 3, korp. 6 117 545 Moscow, RUSSIA TEL: (095) 981-4967 OCEANIA AUSTRALIA/ NEW ZEALAND Roland Corporation Australia Pty. , Ltd. 38 Campbell Avenue Dee Why West, NSW 2099 AUSTRALIA For Australia TEL: (02) 9982 8266 For New Zealand TEL: (09) 3098 715 SLOVAKIA FINLAND Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)9 68 24 020 DAN Acoustic s. r. o. Povazská 18. SK - 940 01 Nové Zámky TEL: (035) 6424 330 CHINA Roland Shanghai Electronics Co. , Ltd. No. 1500 Pingliang Road Shanghai 200090, CHINA TEL: (021) 5580-0800 Roland Shanghai Electronics Co. , Ltd. No. 18 3 Section Anhuaxili Chaoyang District Beijing 100011 CHINA TEL: (010) 6426-5050 Other CENTRAL/ LATIN AMERICA Roland Systems Group U. S. 425 Sequoia Drive Suite 114, Bellingham, Washington, 98226 USA TEL: 360-594-4282 SWEDEN Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. [. . . ]