User manual ONE FOR ALL URC-7730

[. . . ] PLEASE DO NOT DISCARD THIS MANUAL AS YOU MAY NEED IT AGAIN IN THE FUTURE!Your ONE FOR ALL 3 can operate three devices: a Television, a Video Recorder and a DVD Player. 2 WWW. ONEFORALL. COM 2 1 3 4 5 6 7 9 8 10 11 12 13 15/16 14 WWW. ONEFORALL. COM 3 Batteries Your ONE FOR ALL 3 Remote needs 2 new "AA/LR6" Alkaline batteries. Match the batteries to the (+) and (­) marks inside the battery case, then insert the batteries. Replace the battery cover by pushing downwards and allowing it to click back into position. [. . . ] To return to the regular teletext viewing, press the Expand key again, or press the Text key, depending on your television. On some televisions, this may be done by pressing the TEXT key several times. 15 16 TEXT OFF: After pressing the TV key and accessing the text mode, the bottom row of the Video Recorder keys marked red, green, yellow and blue, allow you to access the Fastext functions of your television. If on your original remote control these keys are used for Menu navigation, the ONE FOR ALL Fastext keys may operate in the same way. - For a more detailed explanation of the Teletext and Fastext functions, please refer to the manual of your television. Remember, different televisions control Teletext and Fastext in different ways. Not all Teletext functions may be available for your particular model. WWW. ONEFORALL. COM 5 Setting up the ONE FOR ALL 3 (How to set-up the ONE FOR ALL 3 to control your devices) Direct code set-up Example: To set up the ONE FOR ALL 3 for your television: 1. 2. Make sure your device (television) you wish to operate is switched on (not in standby). A FOR ONE Acura al Admir n Adyso Agazi AGB Agef Aiko 3, 041 0009 0093, 036 0087, 0216 0217, 0264 0516 7, 0087 0009, 003 0216, 0274 1 0037, 0208, 037 0361, Find the code for your device in the Code List (page 12 - 23). Press the device mode key (TV) on the ONE FOR ALL 3 remote for the device you wish to set up. Press and hold down MAGIC until the red light blinks twice (the red light will blink once then twice). 3. Now aim the ONE FOR ALL 3 remote at your device (television) and press POWER. If your device switched off, the ONE FOR ALL 3 is ready to operate your device. - Most TV's do not switch back on pressing the POWER key, please try pressing a "number" key or the "TV-text off" key to switch your TV back on. - If your device does not respond, follow steps 1 through 6 with each code listed for your brand. If none of the codes listed for your brand operate your device, then try the Search Method described on page 7, even if your brand is not listed at all. If your device does not respond or is not functioning properly with one of the codes, try another code listed under your brand. - If the original remote control from your Video Recorder / DVD player did not have a POWER key, press PLAY instead of POWER during step 6. - To set up your other devices, follow the same instructions above, only press the appropriate device key during step 3. - Remember to press the correct device key before operating your device. - Write your device code in the applicable four digit boxes provided in the battery compartment and on page 8 for future reference. Devices can be found under the following keys: Video Recorder Television DVD Player To set up for a second TV, VCR or DVD (See mode re-assignment, Page 9). 6 WWW. ONEFORALL. COM Setting up the ONE FOR ALL 3 Search method --> If your device does not respond to the ONE FOR ALL 3 after you have tried all the codes listed for your brand. [. . . ] 3. 10 WWW. ONEFORALL. COM Trouble Shooting Problem & Solution Problem: Your brand is not listed in the code section?Solution: Try the search method on page 7. A) Try all the codes listed for your brand. Try repeating the Direct Set-Up using another code listed under your brand or start the search method over again to locate the proper code. Enter the program number exactly as you would on your original remote. [. . . ]