User manual ONE FOR ALL URC-7020

[. . . ] URC-7020 701926 UK D F E P I NL Universal remote ONE FOR ALL 2 Table of Contents PICTURE OF THE ONE FOR ALL 2 REMOTE INSTALLING THE BATTERIES FEATURES AND FUNCTIONS INSTALLATION Setting up your devices The Search Method QUICK CODE REFERENCE CHANGING THE MODE OF A DEVICE KEY RESETTING A DEVICE KEY ADVANCED FEATURES Colour and Brightness Volume Punch Through Auto Scan Device Sleeptimer ONE FOR ALL Sleeptimer ONE FOR ALL Recall TROUBLE-SHOOTING Customer Service SETUP CODES Televisions Video Recorders UK 3 4 4 6 7 8 9 9 10 10 10 11 11 12 12 13 80 84 About Your ONE FOR ALL 2 Congratulations on your purchase of the ONE FOR ALL 2 Universal Remote Control. By choosing the ONE FOR ALL 2 remote you have opted for the User Friendly remote control solution. Made according to the highest quality, the ONE FOR ALL 2 will provide you with long-term satisfaction. Please read these enclosed instructions carefully before putting your ONE FOR ALL 2 to use. [. . . ] Device Type 1. _________________________ 2. _________________________ ssss ssss Code 8 WWW. ONEFORALL. COM Changing the Mode of a Device Key With your ONE FOR ALL 2 Remote it is possible to change the mode of a device key. This is useful if you want the ONE FOR ALL 2 to operate more than one of the same device types such as two Televisions or two Video Recorders for example. Example: to program a second Television on the VCR key, you need to change the VCR key into a TV key. 1 MAGIC Press and hold down the MAGIC key until the red light blinks twice (the red light will blink once then twice). 2 2 9 9 Press 9 9 2. The red light will blink twice. 3 Press the TV key (the device mode you want to duplicate). TV 4 VC R Now press the VCR key (the device mode key you want changed) and the red light will blink twice. The VCR key of the ONE FOR ALL 2 is now ready to be set-up for your Television. The ONE FOR ALL 2 will send the command to advance through all the channels available on your television stopping at each channel for about three seconds. Remember, you must aim the ONE FOR ALL 2 at your television the entire time you are using scan. 2 When you find a channel you would like to watch, simply press any key to stop the scan. Important note: Auto Scan may not work with devices that do not have Channel +/- keys on the original remote control. 10 WWW. ONEFORALL. COM Device Sleeptimer If your television has a "Sleeptimer" function built in, you can access this function with your ONE FOR ALL remote. To do so: 1 2 3 Make sure your television is switched on (not in standby). Point the ONE FOR ALL at your television and press and release MAGIC then press POWER. To increase the timer, simply press POWER again (within 5 seconds) until the timer gets to the desired time. To deactivate the Sleeptimer, repeat steps 1-3 above. During step 3, continue pressing POWER (within 5 seconds) until the timer indicates zero minutes. Important note: Depending on how you used the sleeptimer function on your original remote, you might need to access the sleeptimer of your television in a different way (through menu for example). ONE FOR ALL Sleeptimer If your device does not have a sleeptimer function built-in, you can still install the ONE FOR ALL Sleeptimer function. Installing the ONE FOR ALL Sleeptimer: 1 2 3 Press the device key of the device you want to use the sleeptimer on (this is only available for TV). The red light will blink twice again. Now your ONE FOR ALL 2 is setup to use the ONE FOR ALL Sleeptimer on the device you selected in the setup above. To activate the ONE FOR ALL Sleeptimer: It is possible to set the ONE FOR ALL Sleeptimer for 15, 30, 45 or 60 minutes. The red light will blink once to indicate the timer is activated for 15 minutes. To increase the timer, simply press the POWER key again (this must be done within 5 seconds). The red light will blink twice indicating the timer is set for 30 minutes (2x15). This will set the timer to 60 minutes (indicated by 4 blinks). 7 Once you have set the timer to the desired time, set your ONE FOR ALL remote down, pointing it at your device. When the programmed amount of time has elapsed, the ONE FOR ALL 2 will send the command for POWER, thereby turning off your device. Important notes: - The red light on the ONE FOR ALL 2 will blink every 15 seconds indicating that the remote is in sleeptimer mode. - To deactivate the timer, simply press any key on the ONE FOR ALL 2 remote. - Once the ONE FOR ALL Sleeptimer has been installed it is not necessary to repeat steps 1-3 above every time you wish to activate the timer. [. . . ] Pour pouvoir obtenir le service de garantie durant la période de garantie, veuillez nous contacter au numéro mentionné sur la page "Service Consommateurs" pour les instructions nécessaires. Veuillez noter que la preuve d'achat est obligatoire afin de pouvoir déterminer votre droit à ce service. GARANTIA E UNIVERSAL ELECTRONICS/ONE FOR ALL garantiza al comprador que este producto estará libre de defectos materiales o de fabricación, al menos durante 1 año desde la fecha actual de su adquisición , y en caso de que se utilice de un modo normal y correcto. Este producto será sustituido de forma gratuita siempre y cuando se pueda demostrar que es defectuoso y que esto haya sucedido dentro del año de garantía, corriendo a cuenta del comprador los gastos de su devolución. [. . . ]