User manual ONE FOR ALL URC-5800

[. . . ] URC 5800 Cinema 5+ User Guide OVERVIEW Thank you for purchasing the One For All® Cinema 5TM universal remote control with learning. Along with being a complete Home Theater universal remote, the Cinema 5's sophisticated technology will allow you to finally consolidate the clutter of all of the original remotes in your home entertainment system. Through patented learning technology, you can teach your Cinema 5 the unique features of your original remotes and create the complete universal remote control ­ only from One For All. Before you can use your new remote control, you will need to program it to operate the specific home entertainment components you wish to control. [. . . ] Press and hold SETUP until the Cinema 5's red light blinks twice, then release SETUP. Enter the first four-digit DVD or Laser Disc Player code listed for your brand. If performed correctly, the red light will blink twice when entering the final digit. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that works. NOTE: If you have tried all the codes listed for your brand and your DVD or Laser Disc Player does not respond, try using `SEARCHING FOR YOUR CODE". The brands are listed in alphabetical order with the most popular codes listed first. You will use one of these codes to program your Cinema 5 to operate your Receiver/Tuner as follows: 1. Press and hold SETUP until the Cinema 5's red light blinks twice, then release SETUP. Enter the first four-digit Receiver/Tuner code listed for your brand in the "Setup Codes For Receivers/Tuners" section. If performed correctly, the red light will blink twice when you enter the final digit. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find one that works. NOTE: If the unit still does not respond, try using "SEARCHING FOR YOUR CODE". Write your Receiver/Tuner code in the boxes to the left for future reference. 3. 2. 4. 3. 4. Remember, to use your Cinema 5 to operate your Receiver/Tuner, press the RCVR key first. Setup Codes For Receivers/Tuners ADC 0531 Akai 0076 Aiwa 0121, 0158, 0189, 0405 Bang & Olufsen 0898 Capetronic 0531 Carver 0008, 0042, 0189, 0360 Casio 0195 Clarinette 0195 Curtis Mathes 0039, 0080 Denon 0004 Fisher 0042, 0360 Garrard 0463 Harman/Kardon 0110, 0891, 0189 JBL 0110 JVC 0074 Kenwood 0027, 0313, 0314, 0186, 0042 Linn 0189 Lloyd's 0195 LXI 0181 Magnavox 0189, 0195, 0531, 0391 Marantz 0039, 0189 MCS 0039 Modulaire 0195 NAD 0320 Nakamichi 0097 Onkyo 0135, 0380 Optimus 0042, 0080, 0181, 0186, 0531, 0670, 0738, 0801 Panasonic 0039, 0309, 0518 Penney 0195 Philips 0189 Pioneer 0014*, 0080*, 0150, 0531, 0630, 1023 Quasar 0039 RCA 0054, 0360, 0531, 0530 Realistic 0181, 0195 Sansui 0189 Scott 0322 Sharp 0186 Sherwood 0491, 0502 Sony 0158**, 0474 Soundesign 0670 TEAC 0463 Technics 0039, 0309, 0518 Victor 0074 Wards 0014, 0042, 0054, 0080, 0158, 0189 Yamaha 0176, 0186 Yorx 0195 Zenith 0857 *May use Amplifier code 0013 for power and volume. audio setup and codes. 4. Slowly alternate between pressing POWER* and TV until your TV turns OFF. You may have to press this sequence of buttons (POWER* then TV) up to 100 times to search the entire library of codes. When your TV turns OFF, press and release SETUP to lock in the code for your TV. Your Cinema 5 is now programmed to operate your TV. 5. *If you are searching for your VCR, CD, LD or DVD Player code, you may want to play a tape or disk and use the STOP key instead of the POWER key to search for your code. NOTE: To search for the codes of your other components, repeat Steps 1 through 5, only substitute the appropriate device key (ie. , VCR, DVD/LD, RCVR, CD or CBL/SAT) for the component you are searching for. RETRIEVING THE CODES PROGRAMMED INTO THE Cinema 5 If you have set up the Cinema 5 using the "SEARCHING FOR YOUR CODE" procedure, you may want to figure out which four-digit code is operating your equipment. Use this procedure after you have set up your components to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV after setting up your TV using the "SEARCHING FOR YOUR CODE" procedure: 1. Press and hold SETUP until the Cinema 5's red light blinks twice, then release SETUP. For the first digit of your four-digit code, press 1 and count the number of times the red light (LED) blinks on the Cinema 5. [. . . ] If your Cable Converter does not have a sleep timer, press the SLEEP key to activate the Cinema 5's built-in sleep timer. Press and release the CBL/SAT key then press the SLEEP key once to set the Cinema 5's built-in sleep timer for 15 minutes. Each additional press of the SLEEP key will add 15 more minutes to the Sleep Timer, up to a maximum of 60 minutes. The LED will blink twice when the sleep timer is set for 30 minutes, 3 times for 45 minutes, or 4 times for 60 minutes. The red light blinks when you press a key but you receive no response from your home entertainment component? [. . . ]