User manual ONE FOR ALL URC 8011

[. . . ] In TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels. If it does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. 3. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , three blinks = 3) and write down the number. NOTE: If a code digit is "0", the LED will not blink. USING A MACRO With programming, the MACRO key on your One For All 8 Device Home Theater Universal Remote Control can be setup to perform a repetitive, time-consuming operation for easy, convenient access through the press of a single key. [. . . ] However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control's memory. If this happens, please contact our Customer Support department (see Customer Support below) to upgrade the remote control. To obtain warranty service for a defective product during the warranty period, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase. A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective. One For All (330) 405-8655 The default Device Group setting from the factory is: 5. If the device does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter the following sequence: TV, POWER, and 0 - 3 (or 0 -0 - 3 if access is over 100 channels) NOTE: If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e. g. , 0 -7-1-Enter). Restoring Keymoved Keys to Default Settings Restoring A Single Keymoved Key 1. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. Restoring All Keymoved Keys In A Single Mode FEATURES AND FUNCTIONS Use the Key Charts (below) to learn how to use the universal features and functions of the One For All 8 Device Home Theater Universal Remote Control. 6. If you've located a setup code that works, but it has a separate TV code, you'll also need to program it into the remote control to access volume control as follows: a. If correct, the LED will blink twice. NOTE: For VCR/TV Combos programmed with separate TV codes, TV volume is controlled by pressing VCR first and then TV. For other alternatives on controlling your volume keys, see the "Changing Volume Lock" or "Using Keymover" sections. Programming The Home Theater Mode For example, let's assume you have a TV, a cable box, and a VCR in your home theater system. You can set up the Home Theater mode so that selected controls are assigned to these devices as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. For this example, press PLAY once, which will assign the entire group of Transport Controls (i. e. , PLAY, STOP, FWD, REW, PAUSE, and REC) to the VCR. For this example, press VOL+ once, which will assign the entire group of Volume Controls (i. e. , VOL+, VOL-, and MUTE) to the TV. For this example, press CH+ once, which will assign the entire group of Channel Controls (i. e. , CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, and TV/VCR) to the Cable Box. To add additional Menu functionality to the Cable Box, press CBL once. This action will assign the entire group of Menu Controls (i. e. , MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT) to the Cable Box. This action will assign the entire group of PIP Controls (i. e. , PIP, MOVE, and SWAP) to the TV. To exit Home Theater programming, press and hold SET until the LED (red light) blinks twice, then release SET. Key Charts The LED (red light) blinks to show that the remote control is working and is sending signals. [. . . ] LED blinks when you press a key, but home entertainment device does not respond. SOLUTION: Replace batteries with two new AA alkaline batteries. One For All Access 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-3605 One For All Video Expert 4 Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4081 One For All Video Expert Plus 4L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4880 One For All Access 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4605 One For All Access 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-5705 One For All 6 Device Home Theater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-6011 One For All 8 Device Home Theater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-8011 One For All 8L Device Home Theater with Learning Capability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-8811 One For All A/V LCD 8 Device With Learning . . . . . . . . . . . . . . . . . . . . . URC-8910 One For All IR/RF LCD 8 Device With Learning. . . . . . . . . . . . . . . . . . URC-9910 ONE FOR ALL® is the registered trademark of Universal Electronics Inc. Copyright 2002 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written permission of Universal Electronics Inc. The One For All® 8 Device Universal Remote Control is compatibile for use in North America, excluding Mexico. [. . . ]