User manual ONE FOR ALL SV-9325

[. . . ] 5-2 for details. Automatic Shut-Off This function achieves further energy conservation by partially turning OFF the power supply, thereby reducing energy consumption to 15W or less. In the standard setting, Automatic Shut-Off follows Auto Low Power, operating automatically when 60 minutes have elapsed after completion of the last copy, with the copier remaining in the ready to copy state during that time. The time period for the Automatic Shut-Off function can be set for 30 minutes, 60 minutes, 90 minutes, 120 minutes or 240 minutes. 5-3 for details. Automatic Duplex Copying To reduce paper consumption, use this function to make double-sided (duplex) copies, automatically. [. . . ] Make additional application selections, or touch OK to return to the Basic Screen. 50 originals can be set at a time. Option: Press [CHECK] to view the selection, and make the Proof copy, if desired; then touch EXIT to return to the Basic Screen. After copying is completed, press [AUTO RESET] to release the mode and reset the machine. Applications 8-7 Applications Chapter Chapter is used with RADF in 1-2 or 2-2 mode for the purpose of locating title pages on the right side, rather than the reverse side, of a duplex copy. To effectively locate the title page on the right, a blank sheet will be automatically created on the reverse side of a sheet, if required. Ì Scan and store originals into memory, then print all the pages collectively. NOTE: Should memory overflow occur frequently, it is recomended that you contact your Konica service representative to extend the memory capacity in your machine. Ì Use RADF store mode when the original count exceeds 50. Use Platen store mode when originals are not suitable for use with the RADF. title pages: 15 sheets, from 1 ~ 999 Ì Copy mode: 1-2 or 2-2 mode only Ì Incompatible Basic Copying Conditions: 1-1, 2-1 Ì Incompatible Output Modes: Group Ì Incompatible Applications: Sheet/Cover Insertion, Combination, Transparency Interleaving and Thin/Thick Paper modes in Special Paper, Image Insert, Book Copy, Repeat, AUTO Layout, Non-Image Area Erase, OVERLAY 1-sided originals Copies in Chapter mode Tilte page 2-sided originals Title pages 7 5 3 78 5 34 12 4 6 1 Title pages 2 6 2 8 4 6 7 5 3 1 Title page 8-8 Applications 8 Applications Chapter (continued) Application Selection Screen Chapter Page Setting Screen 1 Press [APPLICATION] on the control panel to display the Application Selection Screen. 3 Use the control panel keypad to enter the page number of each title page. To clear an incorrect entry, touch DELETE or press [C] (CLEAR Q'TY). 5 Repeat this for each title page number you want to be located on the right hand side. Be sure to touch SET after each page number entry, up to a total of 15 entries. Option: Touch Booklet on the Chapter Page Setting Screen to use this function. To change the selection of paper tray for copying title pages, touch COPY INSERTION on the screen. 6 7 8 9 When all entries are made, touch OK to return to the Application Selection Screen. 9 Position originals in the document feeder FACE UP and in portrait orientation ( ). Up to 50 originals can be set at a time. Option: Press [CHECK] to view the selection, and make the Proof copy, if desired; then touch EXIT to return to the Basic Screen. After copying is completed, press [AUTO RESET] to release the mode and reset the machine. Applications 8-13 Applications Special Paper Use the following two modes of the Special Paper function to obtain the optimum copying result according to the copy paper type. · Transparency Interleaving mode · Thin/Thick Paper mode Transparency Interleaving Use the Transparency function in 1-2 or 2-1 mode to copy onto overhead projection transparencies, and output a blank or copied interleaf sheet with each copied transparency. In the Blank Sheet Interleaving mode, a blank interleaf sheet is output with each transparency to keep the film material from sticking together. In the Copy Sheet Interleaving mode, a copied interleaf sheet is output along with each transparency copy to provide reference during a presentation as well as providing the means for making additional photocopies for filing and distribution. Ì Ì Ì Ì Ì Ì Ì Ì Ì Transparency source: Multi-sheet bypass tray Print quantity: 1 Multi-sheet bypass tray capacity: 1 transparency sheet AMS is automatically selected. Copy mode: 1-1 or 2-1 only Machine with Finisher discharges transparency by Non-sort only. Incompatible Basic Copying Conditions: 1-2, 2-2, APS Incompatible Output Modes: Sort, Staple, Group Incompatible Applications: Sheet/Cover Insertion, Chapter, Booklet, Thin/Thick Paper mode in Special Paper, Image Insert, Special Original (Mixed Original), Repeat Blank sheets Transparency films Copied sheets Transparency films Original Blank Sheet Interleaving Copy Sheet Interleaving 8-14 Applications Applications Special Paper (continued) Transparency Interleaving (continued) Application Selection Screen Special Paper Mode Selection Screen 1 Load copy paper in tray 1, 2, 3, or 4 to match the size of transparencies. Insert one transparency at a time into the Multisheet bypass tray, and adjust the paper guides. 3 Press [APPLICATION] on the control panel to display the Application Selection Screen. 4 Touch Special Paper to display the Special Paper Mode Selection Screen. [. . . ] Check to make sure paper guides meet the width of mixed size originals. COPY IMAGE IS SKEWED WHEN BYPASS IS USED Be sure copy paper is inserted straight. USING ECM, COPIES CANNOT BE MADE AFTER PASSWORD IS ENTERED Check to see if the message EXCEEDS LIMIT is displayed. Contact key operator to reset limit. FINISHER DOES NOT OPERATE Press Output mode key. Properly close finisher door. RADF INDICATOR WILL NOT LIGHT AFTER AUTO/RESET IS PRESSED Fully close RADF. RADF LIGHT IS FLASHING The document feeder is ready to accept originals. Insert originals on RADF tray, press [AUTO RESET], then [START]. 13-12 Troubleshooting Troubleshooting Troubleshooting Tips (continued) ADD TONER MESSAGE IS DISPLAYED New toner supply is needed. [. . . ]