User manual ONE FOR ALL 8L UNIVERSAL

[. . . ] 8-Device Universal Remote with Learning Control Remoto Universal de 8 Dispositivos con Aprendizaje User's Guide Guía del Usuario OWNER'S MANUAL TABLE OF CONTENTS Introduction . . 15 Unlocking Volume Control for a Single Device (Individual Volume Unlock) . . 42 Setup Codes for Audio Amplifiers (Códigos de Configuración para Amplificadores de Audio) . . 42 Setup Codes for Cable Converters (Códigos de Configuración para Cajas/Convertidores de Cable) 42 Setup Codes for Cable/PVR/DVR Combos (Códigos de Configuración para Aparatos Combinados Cajas/Convertidores de Cable/PVR/DVR). [. . . ] After the master power sequence has been completed, 10 Using Macros OWNER'S MANUAL the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. After programming, point the remote control at the receiver and press the DVD key for at least 2 seconds. This will switch the Receiver's input to input 3, to allow you to view the DVD. PROGRAMMING A MACRO ON A DEVICE KEY In its default state, when you press a device key (e. g. , TV) on the One For All 8L Universal Remote Control with Learning (URC-8820 B00), the remote will switch to that selected device. However, you can also program a Macro onto the Device keys to allow for additional functionality. For example, if your devices are connected to a receiver unit, you can program a Device macro to switch the receiver's input to the selected device. To Program the Device Key Macro For example, let's assume that your DVD in connected to Input 3 of your receiver. You can program a macro that will switch the receiver's input to input 3 when you press and hold the DVD key. Press and hold SET until the LED (red light) blinks twice, then release SET. Press the AUD key (to select the receiver) Press digit 3 (for the input), and press DVD (to return control to the DVD key). To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. NOTE: When you press the device key (e. g. , DVD) for less than 2 seconds, the remote will only select the DVD mode but will not change the Input on the receiver. NOTE: After executing the Device Key Macro, the remote will return to the DVD mode, to allow the control of the DVD device. CLEARING A MACRO 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Select a macro key (e. g. , M1, M2, POWER or any device key) you want to clear and press it once. The macro is now deleted but the keys (in the case of POWER and device keys), will retain their original function. 4. USING CHANNEL SCAN In the TV, VCR, DVD and CBL/SAT modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed, "Programming Favorite Channel Scan" on page 12) and/or all channels for the selected mode. · If Favorite Channel Scan has been set up, scanning of favorite channels will start and cycle through stored channels, then NOTE: You can program up to 20 functions on the Device Key Macro. To Operate the Device Key Macro Using Channel Scan 11 ONE FOR ALL 8L UNIVERSAL REMOTE CONTROL WITH LEARNING proceed to the next channel up and cycle through all channels on the selected device. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, then proceed to the next channel up and cycle through all channels on the selected device. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. The LED will blink twice. USING LEARNING The One For All 8L Universal Remote Control with Learning (URC-8820 B00) includes a Learning feature so you can add functions that are unique to your home entertainment devices (e. g. , DVD EJECT). However, there are some considerations. 3. To stop scanning channels at any time, press any key once. PROGRAMMING FAVORITE CHANNEL SCAN In the TV, VCR, DVD or CBL/SAT mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when you press FAV (see "Using Channel Scan" on page 11). NOTE: Only channels of one mode can be stored for Favorite Channel Scan. [. . . ] Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release. Next enter 9 9 2. Then press the device key to be cleared twice. Now repeat the Searching for Your Code method on page 8. CH+ and CH- do not work for your RCA TV. SOLUTION: PROBLEM: SOLUTION: PROBLEM: PROBLEM: SOLUTION: SOLUTION: PROBLEM: PROBLEM: SOLUTION: SOLUTION: PROBLEM: SOLUTION: PROBLEM: Troubleshooting 17 ONE FOR ALL 8L UNIVERSAL REMOTE CONTROL WITH LEARNING SOLUTION: Due to RCA design (19831987), only the original remote control will operate these functions. See "Changing Volume Lock" on page 15 to lock/ unlock volume. [. . . ]