User manual ONE FOR ALL 3 DEVICES UNIVERSAL REMOTE CONTROL

[. . . ] To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , 3 blinks = 3) and write down the number. NOTE: If a code digit is "0", the LED will not blink. VCR/DVD back to VCR/DVD: SET - 9 - 9 - 2 VCR/DVD VCR/DVD When a re-assignment is done, the LED will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see Programming Device Control). PROBLEM: The unit does not control home entertainment devices or commands are not working properly. attributable to acts of God. OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY, ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. [. . . ] Now, whenever you press VOL+, VOL­, or MUTE, volume will be controlled by your mode choice. PROGRAMMING DEVICE CONTROL The One For All 3 Devices remote control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, and a Toshiba DVD player. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: For TV/VCR Combo control, see the next section. 4. If the device does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (PLAY) key. 5. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking. As before, write down each fourdigit code. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the remote control after entering the channel number. PROBLEM: Tried "Search Method" and still could not find a working code. Unlocking Volume Control: NOTE: Perform these instructions when you want independent volume control for each programmed device (e. g. , TV volume control in TV mode, CBL/SAT volume control in CBL/SAT mode, etc. ) USER'S GUIDE INTRODUCTION The One For All 3 Devices Universal Remote Control is designed to operate three home entertainment devices, depending on the model purchased (see Key Charts, Mode Keys on the right). The remote control requires four fresh AAA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference. When controlling a DVD player, use SKIP FORWARD to next DVD chapter. , use SKIP REVERSE to the last DVD chapter. Press SHIFT and use the Up/Down/Left Right cursor keys to move the cursor in the program guide and menu screens. Press SLEEP to activate your device's sleep timer (not available for all devices). use TV/VID to switch the TV's input to view TV or video program. 1. Turn on a device (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. RE-ASSIGNING DEVICE KEYS The One For All 3 Devices can be set to control a second TV, VCR, or DVD player. For example, to control two TVs, a VCR, and a cable box, you will need to reassign the unused VCR/DVD key to operate the second TV as follows: 1. [. . . ] One For All® 3 Devices is compatibile for use in North America excluding Mexico. URC-3300N/3330 12/01 PROBLEM: Key Charts Use SET for all programming sequences. The LED (red light) blinks to show that the remote control is working and is sending signals. [. . . ]