User manual ONE FOR ALL 10-DEVICE UNIVERSAL REMOTE WITH LEARNING

[. . . ] OFA 10L with Learning Owners Manual. fm Page 0 Thursday, January 27, 2005 1:34 PM 10-Device Universal Remote with Learning Control Remoto Universal de 10 Dispositivos con Aprendizaje User's Guide Guía del Usuario OFA 10L with Learning Owners Manual. fm Page 1 Thursday, January 27, 2005 1:34 PM OWNER'S MANUAL TABLE OF CONTENTS Introduction . . 15 Unlocking Volume Control for a Single Device (Individual Volume Unlock) . . 43 Setup Codes for Audio Amplifiers (Códigos de Configuración para Amplificadores de Audio) . . 43 Setup Codes for Cable Converters (Códigos de Configuración para Cajas/Convertidores de Cable) 43 Setup Codes for Cable/PVR/DVR Combos (Códigos de Configuración para Aparatos Combinados Cajas/Convertidores de Cable/PVR/DVR). [. . . ] Enter the channel number: 5 2. 5. 6. 7. NOTE: If you have access to over 100 channels, enter 0 5 2. Moreover, if the original remote control requires you to press ENTER to change 8. 10 Using Macros OFA 10L with Learning Owners Manual. fm Page 11 Thursday, January 27, 2005 1:34 PM OWNER'S MANUAL To Operate Master Power Macro 1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices. NOTE: When you press POWER for less than 2 seconds, a power command will only be sent to the currently-selected device. Press and hold SET until the LED (red light) blinks twice, then release SET. Press digit 3 (for the input), and press DVD (to return control to the DVD key). To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. NOTE: You can program up to 20 functions on the Device Key Macro. After programming, point the remote control at the receiver and press the DVD key for at least 2 seconds. This will switch the Receiver's input to input 3, to allow you to view the DVD. NOTE: When you press the device key (e. g. , DVD) for less than 2 seconds, the remote will only select the DVD mode but will not change the Input on the receiver. NOTE: After executing the Device Key Macro, the remote will return to the DVD mode, to allow the control of the DVD device. PROGRAMMING A MACRO ON A DEVICE KEY In its default state, when you press a device key (e. g. , TV) on the One For All 10L Universal Remote Control with Learning (URC-10820 B00), the remote will switch to that selected device. However, you can also program a Macro onto the Device keys to allow for additional functionality. For example, if your devices are connected to a receiver unit, you can program a Device macro to switch the receiver's input to the selected device. To Program the Device Key Macro For example, let's assume that your DVD in connected to Input 3 of your receiver. You can program a macro that will switch the receiver's input to input 3 when you press and hold the DVD key. CLEARING A MACRO 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Select a macro key (e. g. , M1, M2, M3 POWER or any device key) you want to clear and press it once. Using Macros 11 OFA 10L with Learning Owners Manual. fm Page 12 Thursday, January 27, 2005 1:34 PM ONE FOR ALL 10L UNIVERSAL REMOTE CONTROL WITH LEARNING 4. The macro is now deleted but the keys (in the case of POWER and device keys), will retain their original function. NOTE: Only channels of one mode can be stored for Favorite Channel Scan. In the TV, VCR, DVD, CBL and SAT modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed, "Programming Favorite Channel Scan" on page 12) and/or all channels for the selected mode. [. . . ] Try readjusting positions of remote controls before performing the procedure again. Tried Searching For Your Code method and still could not find a working code. Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release. Next enter 9 9 2. Then press the device key to be cleared twice. Now repeat the Searching for Your Code method on page 9. [. . . ]