User manual MTD OEM-190-116
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MTD OEM-190-116. We hope that this MTD OEM-190-116 user guide will be useful to you.
Manual abstract: user guide MTD OEM-190-116
Detailed instructions for use are in the User's Guide.
[. . . ] Locate the square hole found in the cutting deck surface by pivoting the discharge chute upward. Install the mulch plug and secure it in place with the carriage screw, bell washer and plastic wing nut as illustrated in Figure 2.
Bell Washer
Plastic Wing Nut
Tractor’s Manufactured Prior to 2001 (without pre-drilled holes)
1. Place the mulch plug drill guide included with this kit in place on the surface (NOT over the lip) of the mulch plug as shown in Figure 3. [. . . ] Release the clamping pliers or C-clamps from the cutting deck and set them aside. Secure both skirt segments by tightening all six screws with a 3/8-inch wrench.
4
38-inch Decks
Right-hand Skirt Segment
Left-hand Skirt Segment
Toe Guard
Make Sure that the RH skirt segment butts flushly up against the toe guard. Make Sure that the deck segments butt flushly up against each other.
IMPORTANT: Line up the deck skirts evenly along the edge of the cutting deck’s front lip. Figure 5
5
Attaching the Deck Skirts
42-inch Decks
The following instructions are for the installation of the mulch kit on tractor’s equipped with a 42-inch deck only. If your tractor is equipped with a 38-inch deck, disregard these instructions and refer to the previous instructions on page 4 under the heading 38-inch Decks.
WARNING: Before attempting to install the mulch kit, move the machine to flat, level ground, disengage PTO, shift to neutral, set parking brake, stop engine and remove key to prevent unintended starting. WARNING: Always wear safety glasses before performing the following instructions.
NOTE: On tractor’s with pre-drilled holes along the cutting deck’s front lip, it is easier, but NOT necessary, to remove the cutting deck from the tractor in order to complete the following steps.
1. Remove the cutting deck as instructed in your tractor’s Operator’s Manual. Clean all debris from the underside of the deck, specifically the area near the front edge. Position the deck skirt segments over the front edge of the cutting deck as illustrated in Figure 6. Use locking pliers or C-clamps to secure the skirt segments in place.
NOTE: On newer-style tractor decks (manufactured in 2001 or later), holes are drilled into the deck at the factory that will align with the holes found in the deck skirt segments.
IMPORTANT: The numeral “42” is stamped into the TOP of each deck skirt segment (when viewed in its operating position). Be certain that the stamped side is facing away from you when positioning the skirt segments over the front edge of the cutting deck, with the deck flipped upside down.
5. On tractor’s without pre-drilled holes, use a hammer and center punch (or large nail) to mark the six locations where it will be necessary to drill holes into the cutting deck. Using a 1/8” bit, carefully drill pilot holes into the cutting deck where the six center-punch marks were made in the step 5. Using a 7/32” bit, carefully drill out the pilot holes just made. Fasten the LH skirt segment in place over the front edge of the cutting deck with three self-tapping screws.
IMPORTANT: Be certain to fasten the deck skirt so that the heads of the screws are on the underside of the cutting deck when it’s in its operating position.
9. Fasten the RH skirt segment in place over the front edge of the cutting deck with the two remaining self-tapping screws. [. . . ] During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth above. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. ) The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. MTD shall not be liable for incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MTD OEM-190-116
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MTD OEM-190-116 will begin.