User manual MTD MC356
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MTD MC356. We hope that this MTD MC356 user guide will be useful to you.
Manual abstract: user guide MTD MC356
Detailed instructions for use are in the User's Guide.
[. . . ] STOP ARRÊT ALTO
USER MANUAL
For problems or questions, DO NOT return this product to the store. For your own safety, please read and follow the safety precautions in this manual before attempting to operate your chain saw. pN 9096-31103 Printed in Taiwan
INTRODUCTION
PLEASE READ
Dear Customer , Thank you for purchasing a McCulloch product. With proper operation and maintenance, it will provide you with years of service. [. . . ] CHAIN BRAKE® MECHANICAL TEST
Your chain saw is equipped with a CHAIN BRAKE® that reduces possibility of injury due to kickback. The brake is activated if pressure is applied against brake lever when, as in the event of kickback, operator’s hand strikes the lever. 3-5A
A
WARNING
The purpose of the CHAIN BRAKE® is to reduce the possibility of injury due to kickback; however, it cannot provide the intended measure of protection if the saw is operated carelessly. Always test the CHAIN BRAKE® before using your saw and periodically while on the job. oFF
3-3F
3-5B
B D D 3-4A
C 3-3G
8
9
4 - FUEL AND LUBRICATION
4-1. FUEL
Use regular grade unleaded gasoline mixed with Genuine Factory Parts 40:1 custom 2-cycle engine oil for best results. This will cause permanent engine damage and void the manufacturer’s warranty for that product. If 2-cycle lubricant other than Genuine Factory Parts Custom Lubricant is to be used, it must be a premium grade oil for 2-cycle air cooled engines mixed at a 40:1 ratio. Do not use any 2-cycle oil product with a recommended mixing ratio of 100:1. If insufficient lubrication is the cause of engine damage, it voids the manufacturer’s engine warranty for that occurrence. ENGINE PRE-START CHECKS
FUEL MIXING TABLE
WARNING
Never start or operate the saw unless the bar and chain are properly installed. Be certain the CHAIN BRAKE® is disengaged (C) before starting unit (Figure 5-1A). Using a Phillips or slotted screwdriver - turn screw 1/4 to 1/2 turn clockwise (to the right). (Figure 5-2H) NOTE: If chain turns while idling - turn screw back to the left until chain stops and unit continues to idle. RECOMMENDED FUELS
Some conventional gasolines are being blended with oxygenates such as alcohol or an ether compound to meet clean air standards. Your McCulloch engine is designed to operate satisfactorily on any gasoline intended for automotive use including oxygenated gasolines. MIXING FUEL
Mix fuel with Genuine Factory Parts brand 2 cycle oil in an approved container. CHAIN AND BAR LUBRICATION
Always refill the chain oil tank each time the fuel tank is refilled. We recommend using Genuine Factory Parts Chain, Bar and Sprocket Oil, which contains additives to reduce friction and wear and to assist in the prevention of pitch formation on the bar and chain. Latch throttle advance: depress latch and hold (C) squeeze throttle trigger (D) release trigger and then the latch. 5-2E) NOTE: If the engine sounds as if it wants to start before the 4th tug, end the tugging of the starter and proceed as described in the next step. 5-2B C 5-2C
Gasoline and Oil Mix 40:1
D
5-2D
5-2E
Oil Only
E
F
5-2F
5-2G
IMPORTANT IDLING INFORMATION
In some cases due to operating conditions (altitude , temperature etc. [. . . ] There may be other quality equivalent replacement components for achieving kickback protection. TOOLS FOR LUBRICATION:
The Lube Gun (optional) is recommended for applying grease to the guide bar sprocket tip. The Lube Gun is equipped with a needle nose tip which is necessary for the efficient application of grease to the sprocket tip. CHAIN MAINTENANCE
CHAIN TENSION:
Check the chain tension frequently and adjust as often as necessary to keep the chain snug on the bar, but loose enough to be pulled around by hand. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MTD MC356
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MTD MC356 will begin.