User manual MTD CUBCADET 7000

[. . . ] SERIES 7000 & *361 23 18( 4VSHYGXW %OXMIRKIWIPPWGLEJX ¤ 7EEVFVµGOIR ¤ +IVQER] English Français Deutsch TABLE OF CONTENTS TO THE OWNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CALLING SERVICE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 RECORDING MODEL AND SERIAL NUMBER INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 USING THE TRACTOR CORRECTLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Push the handle forward to lower front hitch or front loader boom. · Push the handle fully forward until it locks in the detent position to place the front hitch or front loader boom in the float position. · Push the handle to the right to angle (if equipped) the front hitch to the right or dump the loader bucket. · Pull the handle to the left to angle (if equipped) the front hitch to the left or roll back the loader bucket. IMPORTANT: When transporting pull-behind equipment, always use a safety chain to supplement the connection between the tractor and towed equipment. The safety chain must have a strength rating equal to or greater than the gross weight of the equipment being towed. 25 FLOAT HITCH FLOAT BOOM LOWER HITCH LOWER BOOM ANGLE LEFT ROLLBACK BUCKET RH FENDER COVER RAISE HITCH RAISE BOOM ANGLE RIGHT DUMP BUCKET When mounting optional Cub Cadet equipment on the rear of the tractor, such as a rotary tiller, rotary cutting deck, or a rear finish mower, the weight bracket and a minimum of four suitcase weights should be used. For all other rear mounted equipment, follow the guidelines provided in the implement's Operator's Manual to determine how much weight is needed to counterbalance the equipment. If guidelines are not available, ballast the tractor so that a minimum of approximately 40% of the machine weight is on the front wheels. Weighting the Rear of the Tractor Adding weight to the rear of the tractor is not required for most Cub Cadet front mounted equipment currently available for this tractor. However, if installing only the optional front end loader (without the back hoe), weight must be added to the rear of the tractor. The most common methods of adding weight are filling the rear wheels with liquid ballast (usually a calcium chloride and water solution) or mounting a rear weight box. Liquid Ballast Properly filling the rear tires with liquid ballast increases the weight of each rear wheel to approximately 90 kg, which should provide adequate counterbalance. Because special equipment and a familiarity with the practice is required, only a qualified tire technician should perform this procedure. Consult with your Cub Cadet dealer about having liquid ballast added to your tires, and for any special maintenance instructions after the procedure is performed. Rear Weight Box A weight box will provide adequate counterbalance if the following criteria is met: · · The weight box and contents must total a minimum of 90 kg. The weight box must be positioned a minimum of approximately 5. 8 cm rearward of the rear axle, and be carried no more than 30. 4 cm from the ground. Figure 24 "ON DEMAND" FOUR WHEEL DRIVE The "On Demand" Four Wheel Drive system automatically delivers power to the front axle whenever the need for additional traction is sensed by the transmission. TRACTOR WEIGHTING When implements are installed on either the front or rear of the tractor, the normal balance of the tractor is altered. · As a rear mounted implement is raised to the transport position, the balance point of the tractor shifts rearward, which may result in a loss of steering control and tractor stability. · When a front mounted implement is raised, the balance point shifts forward and may result in a loss of traction and stability. To counterbalance these weight shifts, weight should be added to the tractor in the form of either cast iron weights or liquid ballast. However, only enough weight should be added to obtain good traction, control, and stability. Excessive weight will unnecessarily load down the tractor's engine and transmission. NOTE: When adding weight to the tractor, it may be necessary to increase the inflation pressure in the tires. Front Weights To counterbalance three point hitch mounted equipment, a weight bracket/bumper kit and cast iron weights are available from your Cub Cadet dealer. If the weight box is positioned closer to the rear axle or carried higher, additional weight must be added to effectively counterbalance the front loader. 26 SECTION 3: ADJUSTMENTS ADJUSTING THE SEAT For the comfort of the operator, a single lever adjustable seat is provided to set the fore to aft position of the seat. [. . . ] FUEL INJECTOR NOZZLE SERVICE The fuel injector nozzles should be checked and serviced after every 2000 hours of engine operation. Contact your Cub Cadet dealer. · 48 SECTION 6: SPECIFICATIONS Engine Manufacturer . Cub Cadet Hydraulic/Transmission Fluid Transmission Capacity (Includes Hydraulics) . Cub Cadet Gear Lube-135 H. E. P. (85W-140) Front Axle Capacity (Includes RH and LH Final Drives) . [. . . ]