User manual MTD CUBCADET 6000

[. . . ] 769-02993A jqa=mêçÇìÅíë=^âíáÉåÖÉëÉääëÅÜ~Ñí==p~~êÄêÅâÉå==dÉêã~åó 1 14 1 2 HOURS 1/10 3 FUEL RPM E F 0 x1000 4 3 4 5 13 12 11 10 9 8 7 6 4 5 2 15 21 16 17 28 26 18 27 19 20 21 6 22 25 23 24 22 7 8 9 b (b) a (c) (a) (a) (b) 10 B A C G 11 D H K J H N L E F 12 3. 2. 1. 13 (b) (a) 14a 1 2 14b 3 15 b a 16 17 a b 18 19 b MAX a b a MIN 20 c b 21 b a 22 b a a b 23 1 10 2 5 23 20 21 19 18 5 97 17 11 4 3 18 14 16 5 22 12 16 14 6 9 8 15 16 6 16 13 24 a c d 25 b English Français Deutsch Nederlands Svenska Dansk Español 4 23 45 65 85 103 122 English User manual This unit is not intended for purposes beyond those listed above. The user is liable for all damage to third parties and their property. As standard, in its standard configuration, this vehicle is not approved for operation on public roads or for transporting people. [. . . ] The forwards/backwards pedal does not work if the parking brake is locked. Actuating when the parking brake is locked leads to premature wear and tear of the transmission assembly. Note Releasing the differential lock pedal does not always disengage the differential lock. You may have to reduce the tractor's speed or reverse direction (first stop the appliance) before you can disengage the differential lock. Stopping the engine Cool the engine down appropriate to the previous workload. ­ In the case of a high workload: set the throttle to the middle setting and let the engine run for 3­5 minutes. Lock the parking brake. Four wheel drive The four wheel drive automatically switches the front axle drive on if the transmission establishes that the wheels have beeen turned and additional traction is necessary. For this, the user does not have to do anything. Driving the tractor t~êåáåÖ ^Äêìéí=í~âÉçÑÑI=ëíçééáåÖ=ëìÇÇÉåäóI= ~åÇ=ÇêáîáåÖ=~í=ÉñÅÉëëáîÉ=ëéÉÉÇë= ê~áëÉ=íÜÉ=êáëâ=çÑ=~ÅÅáÇÉåíë=~åÇ=Å~å= Å~ìëÉ=Ç~ã~ÖÉ=íç=íÜÉ=ìåáíK=_É= ÉëéÉÅá~ääó=Å~ìíáçìë=ïÜÉå=êÉîÉêëáåÖK= kÉîÉê=ÅÜ~åÖÉ=íÜÉ=ÇáêÉÅíáçå=çÑ=íê~îÉä= çê=íÜÉ=ëéÉÉÇ=ïáíÜçìí=Ñáêëí=ÄêáåÖáåÖ= íÜÉ=îÉÜáÅäÉ=íç=~=ëí~åÇK kÉîÉê=ëÉíL~Çàìëí=íÜÉ=ÇêáîÉêÛë=ëÉ~í= ïÜáäÉ=íÜÉ=ìåáí=áë=ãçîáåÖK Set the driver seat. Raise the attachments which are mounted to the 3 point attachment device. Set the drive lever to the optimum range for the job (as a rule, maximum). Release the brake pedal and slowly actuate the forwards/ backwards pedal until the desired speed has been reached. Before starting the journey, make sure that the front wheels are in the desired direction. Stopping/Parking the tractor Release the accelerator and step on the brake pedal until the vehicle comes to a stand. Engage the parking brake and remove the ignition key before leaving the appliance. ! Using the 3 point attachment device t~êåáåÖ _ÉÑçêÉ=ìëáåÖ=íÜÉ=P=éçáåí=~íí~ÅÜãÉåí= ÇÉîáÅÉ=çê=EìåJFÜççâáåÖ=~ÅÉëëçêáÉëI= ~äï~óë=ëïáíÅÜ=íÜÉ=mql=~åÇ=íÜÉ= ÉåÖáåÉ=çÑÑK=t~áí=ìåíáä=íÜÉ=íê~ÅíáîÉ=ìåáí= áë=ÄêçìÖÜí=íç=~=ëí~åÇK Switching the differential lock on and off t~êåáåÖ= oáëâ=çÑ=~å=~ÅÅáÇÉåí=çÅÅìêêáåÖ=~åÇ= Ç~ã~ÖÉ=íç=íÜÉ=îÉÜáÅäÉK Ó låäó=ëïáíÅÜ=íÜÉ=ÇáÑÑÉêÉåíá~ä=äçÅâ=çå= ïÜÉå=íÜÉ=îÉÜáÅäÉ=áë=~í=~=ëí~åÇK Ó aç=åçí=~Åíì~íÉ=íÜÉ=ÇáÑÑÉêÉåíá~ä=äçÅâ= ïÜÉå=ÇêáîáåÖ=çå=íÜÉ=êç~Ç= EÜ~êÇÉåÉÇ=ëìêÑ~ÅÉF=~åÇ=~í=ëéÉÉÇ= EëíÉÉêáåÖ=ÇáÑÑáÅìäíáÉë=Ó=êáëâ=çÑ=~å= ~ÅÅáÇÉåíFK Note The vehicle is equipped with an automatic four wheel drive which additionally powers the fromt axles if required. The differential lock is activated (even transfer of power onto both rear wheels). Setting the 3 point attachment device Fig. 17 The adjustable lifting arm on the right can be set in order to position the lower transverse links Loosen the counter nuts (a) and turn the setting pipe (b) in order to shorten or lengthen the lifting coupling. 18 The length of the upper transverse link is normally determined by the shape of the acessory. In order to set the upper transverse link, loosen the locking lever (a) and turn the setting pipe (b). Tilt the locking lever back again if the desired length is not reached. Set correctly, the upper transverse link lies parallel or almost parallel to the lower transverse links. 12 User manual Fig. 19 The length of the lower transverse link bracing at each of the lower transverse links limit the lateral movement of the lower transverse links. Loosen the counter nuts (a) and turn the hex collar (b) in order to adjust the length of the lower transverse link bracing. Note In order to lift an attachment using the 3 point attachment device, the engine must be running. 9 English Engaging the cutting mechanism or other driven accessories Start the engine. [. . . ] After bringing into line, carefully pull the mounting out of the tail light reflector. Bring the tounges on the mounting into line with the notches in the reflector and carefully push the mounting into place. Tightly turn the mounting in a clockwise direction. Over-inflating reduces the longevity of the tyres. Tyre pressure should be checked before every journey. Notes concerning wheel change t~êåáåÖ låäó=ìëÉ=~ééêçîÉÇ=îÉÜáÅäÉ=à~ÅâëK= Work safely. [. . . ]